☺ Buildbot (Sourceware): binutils-gdb - build successful (master)

A restored build has been detected on builder binutils-fedora-arm64 while building binutils-gdb.

Full details are available at:
    https://builder.sourceware.org/buildbot/#/builders/176/builds/6168

Build state: build successful
Revision: ee7506d8ffbec39df2262f08a348346914d71efd
Worker: fedora-arm64
Build Reason: (unknown)
Blamelist: Jan Beulich <[email protected]>, LIU Hao <[email protected]>, Zhongteng Gui <[email protected]>

Steps:

- 0: worker_preparation ( success )

- 1: git checkout ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/1/logs/stdio

- 2: rm -rf binutils-build ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/2/logs/stdio

- 3: configure ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/3/logs/stdio
        - config.log: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/3/logs/config_log

- 4: make ( warnings )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/4/logs/stdio
        - warnings (47): https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/4/logs/warnings__47_

- 5: make check (no ld) ( warnings )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/5/logs/stdio
        - gas.sum: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/5/logs/gas_sum
        - gas.log: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/5/logs/gas_log
        - binutils.sum: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/5/logs/binutils_sum
        - binutils.log: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/5/logs/binutils_log
        - libsframe.sum: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/5/logs/libsframe_sum
        - libsframe.log: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/5/logs/libsframe_log
        - libctf.sum: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/5/logs/libctf_sum
        - libctf.log: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/5/logs/libctf_log
        - warnings (12): https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/5/logs/warnings__12_

- 6: make check ld ( warnings )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/6/logs/stdio
        - ld.sum: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/6/logs/ld_sum
        - ld.log: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/6/logs/ld_log
        - warnings (3): https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/6/logs/warnings__3_

- 7: prep ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/7/logs/stdio

- 8: collect system versions ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/8/logs/stdio

- 9: fetch .bunsen.* ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/9/logs/stdio

- 10: build bunsen.cpio.gz ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/10/logs/stdio

- 11: fetch bunsen.cpio.gz ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/11/logs/stdio

- 12: unpack bunsen.cpio.gz ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/12/logs/stdio

- 13: pass .bunsen.source.* ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/13/logs/stdio

- 14: upload to bunsen ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/14/logs/stdio

- 15: clean up ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/15/logs/stdio

- 16: rm -rf binutils-build_1 ( success )
    Logs:
        - stdio: https://builder.sourceware.org/buildbot/#/builders/176/builds/6168/steps/16/logs/stdio