Re: Using mingw-pkg to build gcc 5.3.0

-----BEGIN PGP SIGNED MESSAGE-----
Hash: SHA1

On 29/12/16 00:03, David Gressett wrote:
>> Conventionally; assuming you unpacked to $HOME/mingw-pkg-0.1.0:
>>
>>   $ mkdir $HOME/mingw-pkg-0.1.0/build
>>   $ cd $HOME/mingw-pkg-0.1.0/build
>>   $ ../configure && make && make install
> 
> No joy - I get
> sh: ../configure: No such file or directory

So, you need to run autoconf, to generate it from configure.ac:

  $ cd $HOME/mingw-pkg-0.1.0
  $ autoconf

Then you can cd to the build subdirectory, and the conventional
build sequence should run, as above.  (You may also wish to delete
the entire autom4te.cache subdirectory, created by autoconf; it is
of no further use to you).

- -- 
Regards,
Keith.

Public key available from keys.gnupg.net
Key fingerprint: C19E C018 1547 DE50 E1D4 8F53 C0AD 36C6 347E 5A3F
-----BEGIN PGP SIGNATURE-----
Version: GnuPG v2.0.20 (GNU/Linux)
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=ccUL
-----END PGP SIGNATURE-----

------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most 
engaging tech sites, SlashDot.org! http://sdm.link/slashdot