Re: Giving up...(maybe??!!)

"ShuJian" <[email protected]>
Newsgroups gmane.comp.handhelds.linux.intimate
Message-ID <[email protected]>
Hi,
I am using the network 192.168.123.*,
you need to change 123 to 0 for your network.
And, change the IP to you IP address. I am not
using DHCP. So, I am not sure if it works under
DHCP. Anyway, DHCP should work by default. 

I attache my version of the network.opts.
Change DNS_1 to your local DNS. 

Hope it helps.
jian 

 ---------------------------------- 

case "$ADDRESS" in
*,*,*,*) 

INFO="Sample private network setup"
# Transceiver selection, for some cards -- see 'man ifport'
IF_PORT=""
# Use BOOTP (via /sbin/bootpc, or /sbin/pump)? [y/n]
BOOTP="n"
# Use DHCP (via /sbin/dhcpcd, /sbin/dhclient, or /sbin/pump)? [y/n]
DHCP="x"
PUMP='x'
# If you need to explicitly specify a hostname for DHCP requests
DHCP_HOSTNAME=""
# Host's IP address, netmask, network address, broadcast address
IPADDR="192.168.123.12" 

NETMASK="255.255.255.0"
NETWORK="192.168.123.0"
BROADCAST="192.168.123.255"
# Gateway address for static routing
   GATEWAY="192.168.123.1"
# Things to add to /etc/resolv.conf for this interface
DOMAIN=""
SEARCH=""
DNS_1="165.21.100.88"
DNS_2=""
DNS_3=""
# NFS mounts, should be listed in /etc/fstab
MOUNTS=""
# If you need to override the interface's MTU...
MTU=""
# For IPX interfaces, the frame type and network number
IPX_FRAME=""
IPX_NETNUM=""
# Extra stuff to do after setting up the interface
start_fn () { return; }
# Extra stuff to do before shutting down the interface
stop_fn () { return; }
# Card eject policy options
NO_CHECK=n
NO_FUSER=n
;;
esac 

 --------------------------------
> Thnak you for your advice. It helps a lot. I hope I can ask you a few
> questions now....I reinstalled Fam 0.5, in order to get Intimate, one more
> time. I modified /etc/pcmcia/config again, and the FA411 is recognised and
> initialised. I haven't touched /etc/pcmcia/network.opts yet.
> I was hoping you could give me some advice on this. I use a Netgear router
> (RM356) to share my internet connection with my PCs. It provide DHCP and
> does NAT. Its address is 192.168.0.1 and it is also the default gateway. How
> should I modify the network.opts file to reflect my network?? Also, after a
> couple of minutes cardmgr comes up with an error and eth0, the FA411,
> disappears. Is that because I haven't configured network.opts properly?
> Please, any help would be GREATLY appreciated. I really WANT to run Intimate
> on the iPaq.
> Thank you so much in advance for your time and attention. 
> 
> Roberto Migliorati. 
> 
> -----Original Message-----
> From: shujian [mailto:[email protected]]
> Sent: Friday, 15 February 2002 7:42 PM
> To: Roberto Migliorati
> Subject: Re: [Intimate] Giving up...(maybe??!!) 
> 
> 
>> First of all the ethernet card: D-link DFE 650TX, which on handhelds.org
> is
>> reported to work 'out of the box'....well, it isn't.
>> Various attempt to get it working got me nowhere. Took it back and got a
>> Netgear FA411, modified /etc/pcmcia/config accordingly...to no avail. At
>> boot the card was recognised and configured, but no link at all
> whatsoever.
>> Very, very strange....
> 
> Did you modify your network.opts ? It is the setting in this file taking
> effects
> for network accessing. I am using Netgear FA411. It works fine for v0.5.1. 
> 
> Also, I am running 1GB micro-drive. 
> 
> 
> _______________________________________________
> Full Blown Linux on Handheld Devices.
> Intimate mailing list
> [email protected]
> http://handhelds.org/mailman/listinfo/intimate
 


INTRAMEDIA PTE LTD
3B Trengganu Street
Singapore 058457 


[Main]    324 9315
[DID]     324 5993
[Fax]     372 1639
[Mobile]  96359678
[URL]     http://www.intramedia.com.sg 

This e-mail is confidential and may well also be legally privileged. If
you have received it in error, you are on notice of its status. Please
notify us immediately by reply e-mail and then delete this message from
your system. Please do not copy it or use it for any purposes, or
disclose its contents to any other person: to do so could be a breach of
confidence. Thank you for your co-operation. Please
mailto:[email protected] if you need assistance.
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.