Re: Rate limit

Arkada=C5=9F=C4=B1m kullan=C4=B1c=C4=B1 bazl=C4=B1 olacaksa bunun i=C3=A7in=
 qos yapman=C4=B1 =C3=B6neririm bu daha y=C3=B6netilebilir olur serial int =
veya wan int lerde kullan=C4=B1lan rate-limit daha =C3=A7ok me devrelerinde=
 hatt=C4=B1 s=C4=B1n=C4=B1rlamak i=C3=A7in kullan=C4=B1l=C4=B1yor yani kull=
an=C4=B1c=C4=B1y=C4=B1da k=C4=B1s=C4=B1tlars=C4=B1n bunda bir yanl=C4=B1=C5=
=9Fl=C4=B1k yok fakat qos yaparak in y=C3=B6n=C3=BCnde police c=C4=B1r uygu=
layablirsin.
=C2=A0
interface Serial0/0 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0=20
=C2=A0bandwidth 2048 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0=20
=C2=A0ip address 100.1.1.2 255.255.255.252 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=
=A0=20
=C2=A0rate-limit input access-group 111=C2=A01024000 8000 8000 conform-acti=
on transmit exceed-action drop=20
=C2=A0clock rate 2000000 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0=20
! =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0=20
router ospf 1 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0=20
=C2=A0log-adjacency-changes =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0=20
=C2=A0network 100.1.1.2 0.0.0.0 area 2 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0=20
=C2=A0network 192.168.2.0 0.0.0.255 area 2 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=
=A0=20
=C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0 =C2=A0=20
access-list 111 permit ip 192.168.10.0 0.0.0.255 any =C2=A0 =C2=A0 =C2=A0=20


________________________________
From: Ahmet KAFTAN <[email protected]>
To: "[email protected]" <[email protected]>
Sent: Friday, September 30, 2011 10:19 AM
Subject: [cisco-ttl] Rate limit


=C2=A0=20
Merhabalar,

7206 Vxr da, yaklasik 1000 kullanici icin download yonunde rate-limit yapma=
k istiyorum, ornegin kullanicilar 1,2 veya 4 Mbit hiz icin limit koymak ist=
iyorum, kullanicilarin ip leri degismeyeceginden bunu kullanicinin ip adres=
ine gore yapmam gerekecek. Ben soyle iki farkli yaklasimda bulundum. Bu isi=
 yapmanin acaba farkli bir yolu var midir ya da benim gittigim yol dogru yo=
l mudur?

1.

access-list 103 permit ip any host 10.17.0.12

interface gigabit 0/2=20

rate-limit output access-group 103 800000 150000 300000 conform--action tra=
nsmit exceed-action drop

2.access-list 2002 permit ip any host 10.17.0.12
class-map match-all ALI
=C2=A0match access-group 2002
!
!
policy-map 1M
=C2=A0class ALI
=C2=A0=C2=A0 police cir 8000000 bc 1500000 be 3000000
=C2=A0=C2=A0=C2=A0=C2=A0 conform-action transmit
=C2=A0=C2=A0=C2=A0=C2=A0 exceed-action drop
=C2=A0=C2=A0=C2=A0=C2=A0 violate-action drop
!

[Non-text portions of this message have been removed]




[Non-text portions of this message have been removed]



------------------------------------

--
Cisco Teknik Tartisma Listesi (Cisco-ttl)

Disclaimer: Some of the individuals posting to this site, including=20
the moderators, work for Cisco Systems, Inc. Opinions expressed here and in=
 any corresponding comments are the personal opinions of the original autho=
rs, not those of Cisco.
 Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/cisco-ttl/

<*> Your email settings:
    Individual Email | Traditional

<*> To change settings online go to:
    http://groups.yahoo.com/group/cisco-ttl/join
    (Yahoo! ID required)

<*> To change settings via email:
    [email protected]=20
    [email protected]

<*> To unsubscribe from this group, send an email to:
    [email protected]

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/