Help with completely unknown remote

Richard Evans <[email protected]> Tue, 26 Feb 2019 16:56:22 +0000

Newsgroups	gmane.comp.hardware.lirc
Message-ID	<[email protected]>

Hi

I'm trying to configure LIRC for a strange remote for a stair lift, with 
just two buttons - up and down.

I've tried:

_irrecord in default mode: _

gets the signals, sees the gap, but however many times I press the 
buttons, it never terminates, just filling the screen with dots.
_
__irrecord in raw mode: _

works, I can get a good config file with raw codes and can send signals 
via lircd. However for cleanliness I'd like a non-raw config file.
_
__irscrutinzer: _

gets signals, but cannot decode them, writing a conf file in raw mode gives

      begin raw_codes
          #  not renderable, skipped
      end raw_codes

I'm using the irtoy driver reading from an irdroid USB transceiver on a 
raspberry pi.  lirc version 0.10.

I've run mode2 -m for each button, results attached.

The raw config file written by irrecord is:

begin remote

   name  sta1
   flags RAW_CODES
   eps            30
   aeps          100

   gap          120905

       begin raw_codes

           name KEY_UP
               810    1898     447    1898     447

           name KEY_DOWN
               810    1919     447     981     831

       end raw_codes

end remote

So I'm just wondering if there is anything else I should try?  I can 
probably get by with the raw codes (I want this for transmit only) but 
would like to be able to contribute a finished config file if possible.

Thanks

Richard

up-m.txt (text/plain, 1.2 KB)

  1000000

      810     1898      447     1898      447   120917

      831     1919      447     1898      447   120917

      831     1919      447     1898      447   120938

      831     1919      447     1898      447   120917

      831     1919      447     1898      447   120917

      831     1898      447     1898      447   120938

      831     1898      447     1898      447   120917

      831     1898      447     1898      447   120917

      831     1898      447     1898      447   120938

      831     1898      447     1898      447   120917

      831     1898      447     1898      447   120917

      831     1898      447     1898      447   120938

      831     1898      447     1898      447   120917

      831     1898      447     1898      447   120917

      831     1919      447     1898      447   120938

      831     1898      447     1898      447   120917

      831     1898      447     1898      447   120917

      831     1919      447     1898      447   120938

      831     1898      447     1898      447   120917

      831     1898      447     1898      447   120874

      831     1898      447      981      447    99477

      831     1898      447      981      447

down-m.txt (text/plain, 1 KB)

  1000000

      810     1898      447      981      831   120895

      831     1898      447      981      831   120895

      831     1898      447      981      831   120917

      831     1898      447      981      831   120895

      831     1898      447      981      831   120895

      831     1898      447      981      831   120917

      831     1898      447      981      831   120895

      831     1898      447      981      831   120895

      831     1898      447      981      831   120917

      831     1898      447      981      831   120895

      831     1898      447      981      831   120895

      831     1898      447      981      831   120917

      831     1898      447      981      831   120895

      831     1898      447      981      831   120895

      831     1898      447      981      831   120917

      831     1898      447      981      831   120895

      831     1898      447      981      831   120874

      831     1898      447      981      447    99477

      831     1898      447      981      447  1000000