Re: [EE] PCB manufacture

I have tried circuitmaker but it does not recognize my Protel format
netlist files with extension ..net
Is that the extension for a Protel net list?
__________________________________________
David C Brown
43 Bings Road
Whaley Bridge
High Peak                           Phone: 01663 733236
Derbyshire                eMail: [email protected]
SK23 7ND          web: www.bings-knowle.co.uk/dcb
<http://www.jb.man.ac.uk/~dcb>



*Sent from my etch-a-sketch*


On Sun, 27 Oct 2024 at 15:31, Jesse Lackey <[email protected]>
wrote:

> Hi, you may well know this already, that Altium also ha CircuitStudio
> and CircuitMaker, the latter of which is free for
> makers/open-source/nonprofits.  I have not used them.  (I remain on the
> $2500/year subscription train)
>
> J
>
> David C Brown wrote:
> > Yes PCBway and JLC look favourite.
> >
> > Nexr.  What is a good layout package ?
> > My schematics are in TinyCad.   I currently generate a Protel net list
> > which Import into VeeCad for stripboard design.
> > But I am finding stripboard increasingly unsatisfactory and want to move
> to
> > proper PCBs.  I have a lot of experience using ALTIUM but that is too
> > expensive
> > __________________________________________
> > David C Brown
> > 43 Bings Road
> > Whaley Bridge
> > High Peak                           Phone: 01663 733236
> > Derbyshire                eMail: [email protected]
> > SK23 7ND          web: www.bings-knowle.co.uk/dcb
> > <http://www.jb.man.ac.uk/~dcb>
> >
> >
> >
> > *Sent from my etch-a-sketch*
> >
> >
> > On Fri, 25 Oct 2024 at 21:50, Clint Jay <[email protected]> wrote:
> >
> >> I think it depends how fast you want the PCBs, I've used JLC a few times
> >> now and never paid much more than a tenner for 5 or 10 boards Inc
> shipping
> >> by using the China Post option.
> >>
> >> On Fri, 25 Oct 2024, 21:44 David C Brown, <[email protected]> wrote:
> >>
> >>> pc way are cheap but transatlantic shopping inflated the cost
> enourmously
> >>>
> >>> On Fri, Oct 25, 2024, 13:01 Gordon Williams <[email protected]> wrote:
> >>>
> >>>> I've used PCBway with good results.  The prototype board service is
> >> very
> >>>> inexpensive.
> >>>>
> >>>> Gordon
> >>>>
> >>>>
> >>>> On 2024-10-25 9:38 a.m., David C Brown wrote:
> >>>>> Apologies that this must have been asked before,
> >>>>> Can anyone recommend manufacturers of one off PCBs in the UK?
> >>>>> I am looking to single or possibly double sided with solder resist
> >>>>> __________________________________________
> >>>>> David C Brown
> >>>>> 43 Bings Road
> >>>>> Whaley Bridge
> >>>>> High Peak                           Phone: 01663 733236
> >>>>> Derbyshire                eMail: [email protected]
> >>>>> SK23 7ND          web: www.bings-knowle.co.uk/dcb
> >>>>> <http://www.jb.man.ac.uk/~dcb>
> >>>>>
> >>>>>
> >>>>>
> >>>>> *Sent from my etch-a-sketch*
> >>>> --
> >>>> http://www.piclist.com/techref/piclist PIC/SX FAQ & list archive
> >>>> View/change your membership options at
> >>>> https://mailman.mit.edu/mailman/listinfo/piclist
> >>>>
> >>> --
> >>> http://www.piclist.com/techref/piclist PIC/SX FAQ & list archive
> >>> View/change your membership options at
> >>> https://mailman.mit.edu/mailman/listinfo/piclist
> >>>
> >> --
> >> http://www.piclist.com/techref/piclist PIC/SX FAQ & list archive
> >> View/change your membership options at
> >> https://mailman.mit.edu/mailman/listinfo/piclist
> >>
> --
> http://www.piclist.com/techref/piclist PIC/SX FAQ & list archive
> View/change your membership options at
> https://mailman.mit.edu/mailman/listinfo/piclist
>