Re: [EE] PCB manufacture
Jesse Lackey <[email protected]>
| Newsgroups | gmane.comp.hardware.microcontrollers.pic |
|---|---|
| Message-ID | <[email protected]> |
Hi David, sorry I have no idea. J David C Brown wrote: > I have tried circuitmaker but it does not recognize my Protel format > netlist files with extension ..net > Is that the extension for a Protel net list? > __________________________________________ > David C Brown > 43 Bings Road > Whaley Bridge > High Peak Phone: 01663 733236 > Derbyshire eMail: [email protected] > SK23 7ND web: www.bings-knowle.co.uk/dcb > <http://www.jb.man.ac.uk/~dcb> > > > > *Sent from my etch-a-sketch* > > > On Sun, 27 Oct 2024 at 15:31, Jesse Lackey <[email protected]> > wrote: > >> Hi, you may well know this already, that Altium also ha CircuitStudio >> and CircuitMaker, the latter of which is free for >> makers/open-source/nonprofits. I have not used them. (I remain on the >> $2500/year subscription train) >> >> J >> >> David C Brown wrote: >>> Yes PCBway and JLC look favourite. >>> >>> Nexr. What is a good layout package ? >>> My schematics are in TinyCad. I currently generate a Protel net list >>> which Import into VeeCad for stripboard design. >>> But I am finding stripboard increasingly unsatisfactory and want to move >> to >>> proper PCBs. I have a lot of experience using ALTIUM but that is too >>> expensive >>> __________________________________________ >>> David C Brown >>> 43 Bings Road >>> Whaley Bridge >>> High Peak Phone: 01663 733236 >>> Derbyshire eMail: [email protected] >>> SK23 7ND web: www.bings-knowle.co.uk/dcb >>> <http://www.jb.man.ac.uk/~dcb> >>> >>> >>> >>> *Sent from my etch-a-sketch* >>> >>> >>> On Fri, 25 Oct 2024 at 21:50, Clint Jay <[email protected]> wrote: >>> >>>> I think it depends how fast you want the PCBs, I've used JLC a few times >>>> now and never paid much more than a tenner for 5 or 10 boards Inc >> shipping >>>> by using the China Post option. >>>> >>>> On Fri, 25 Oct 2024, 21:44 David C Brown, <[email protected]> wrote: >>>> >>>>> pc way are cheap but transatlantic shopping inflated the cost >> enourmously >>>>> >>>>> On Fri, Oct 25, 2024, 13:01 Gordon Williams <[email protected]> wrote: >>>>> >>>>>> I've used PCBway with good results. The prototype board service is >>>> very >>>>>> inexpensive. >>>>>> >>>>>> Gordon >>>>>> >>>>>> >>>>>> On 2024-10-25 9:38 a.m., David C Brown wrote: >>>>>>> Apologies that this must have been asked before, >>>>>>> Can anyone recommend manufacturers of one off PCBs in the UK? >>>>>>> I am looking to single or possibly double sided with solder resist >>>>>>> __________________________________________ >>>>>>> David C Brown >>>>>>> 43 Bings Road >>>>>>> Whaley Bridge >>>>>>> High Peak Phone: 01663 733236 >>>>>>> Derbyshire eMail: [email protected] >>>>>>> SK23 7ND web: www.bings-knowle.co.uk/dcb >>>>>>> <http://www.jb.man.ac.uk/~dcb> >>>>>>> >>>>>>> >>>>>>> >>>>>>> *Sent from my etch-a-sketch* >>>>>> -- >>>>>> http://www.piclist.com/techref/piclist PIC/SX FAQ & list archive >>>>>> View/change your membership options at >>>>>> https://mailman.mit.edu/mailman/listinfo/piclist >>>>>> >>>>> -- >>>>> http://www.piclist.com/techref/piclist PIC/SX FAQ & list archive >>>>> View/change your membership options at >>>>> https://mailman.mit.edu/mailman/listinfo/piclist >>>>> >>>> -- >>>> http://www.piclist.com/techref/piclist PIC/SX FAQ & list archive >>>> View/change your membership options at >>>> https://mailman.mit.edu/mailman/listinfo/piclist >>>> >> -- >> http://www.piclist.com/techref/piclist PIC/SX FAQ & list archive >> View/change your membership options at >> https://mailman.mit.edu/mailman/listinfo/piclist >>