RE: How can I access the TINI IO Ports

Or you could use the EMAC SOM400EM tini module and carrier, instead of the
reference board, which comes equipped with a character LCD port, Java
classes to support it, plenty of IO pins, etc, etc....

http://www.emacinc.com/som/som400em.htm

NZG.

-----Original Message-----
From: tini-admin-6tN4nzCoH/[email protected] [mailto:[email protected]]On Behalf Of
Kelly Smith
Sent: Wednesday, March 10, 2004 6:50 PM
To: tini-6tN4nzCoH/[email protected]; Jing Qiu
Cc: 1-WIRE
Subject: RE: [TINI]How can I access the TINI IO Ports


Dear Jinq - You could use the AAG Electronica's 1-Wire LCD display
interfaced to TINI's 1-Wire I/O.  Ref:  http://www.aagelectronica.com/aag/

Click on:  1-Wire Sensors & Actuators, and the "Click here" after,

TAI8590 1-Wire Text User Interface

I have one and it works very nice; and includes provisions for switch
closure detection.  It uses the DS2408 1-Wire 8-bit PIO.  So, you don't need
ANY parallel I/O bits at all!

"Based on the Dallas Semiconductor DS2408 the TAI8590 1-Wire Text User
Interface allow you to connect a LCD Character display to your 1-Wire
network and recieve messages from the host system. Also included in the
module is the capability to connect push buttons to allow you to interact
with the host program on your system. This module is fully compatible with
the rest of  TAI 1-Wire devices. Software to test the module and Java
classes are available at no cost in our Download Area."

Best regards, Kelly Smith

-----Original Message-----
From: tini-admin-6tN4nzCoH/[email protected] [mailto:[email protected]]On Behalf Of
Jing Qiu
Sent: Wednesday, March 10, 2004 10:08 AM
To: tini-6tN4nzCoH/[email protected]
Subject: Re: [TINI]How can I access the TINI IO Ports


Thanks. I want to connect an LCD to the DSTINIs400
socket, but as you said, there's only a few IO port
pins available. I see there are 32 user parallel IO
pins available. How to use these user PIOs to access
the data/address/control BUS?

 --- Bryan Armstrong <bryan.armstrong-6tN4nzCoH/[email protected]>
wrote: > Jing Qiu wrote:
> > I'm using DSTINIs400 socket, could anybody show me
> > where's the TINI IO ports, as I couldn't find them
> on
> > the datasheet.
>
> Look for pin names such as P0,P1,P2,P3,etc.  Some
> ports are not
> accessible as they are used for address/data/chip
> enables.
>
> --
> --
> Bryan Armstrong
> bryan.armstrong-6tN4nzCoH/[email protected]
>
>

______________________________________________________________________
Post your free ad now! http://personals.yahoo.ca
_______________________________________________
TINI mailing list
TINI-6tN4nzCoH/[email protected]
To UNSUBSCRIBE, edit your profile, or see list archives:
http://lists.dalsemi.com/mailman/listinfo/tini


_______________________________________________
TINI mailing list
TINI-6tN4nzCoH/[email protected]
To UNSUBSCRIBE, edit your profile, or see list archives:
http://lists.dalsemi.com/mailman/listinfo/tini



_______________________________________________
TINI mailing list
TINI-6tN4nzCoH/[email protected]
To UNSUBSCRIBE, edit your profile, or see list archives:
http://lists.dalsemi.com/mailman/listinfo/tini