RE: How can I access the TINI IO Ports

Thank you guys.
but the problem here is I'm doing my final year
project and I may not have enough time to purchase the
part and wait for another 1 or 2 weeks to get it. So
directly interfacing it onto the TINI socket is my
first option if it's possible.
 --- NZG <[email protected]> wrote: > Or you
could use the EMAC SOM400EM tini module and
> carrier, instead of the
> reference board, which comes equipped with a
> character LCD port, Java
> classes to support it, plenty of IO pins, etc,
> etc....
> 
> http://www.emacinc.com/som/som400em.htm
> 
> NZG.
> 
> -----Original Message-----
> From: tini-admin-6tN4nzCoH/[email protected]
> [mailto:tini-admin-6tN4nzCoH/[email protected]]On Behalf Of
> Kelly Smith
> Sent: Wednesday, March 10, 2004 6:50 PM
> To: tini-6tN4nzCoH/[email protected]; Jing Qiu
> Cc: 1-WIRE
> Subject: RE: [TINI]How can I access the TINI IO
> Ports
> 
> 
> Dear Jinq - You could use the AAG Electronica's
> 1-Wire LCD display
> interfaced to TINI's 1-Wire I/O.  Ref: 
> http://www.aagelectronica.com/aag/
> 
> Click on:  1-Wire Sensors & Actuators, and the
> "Click here" after,
> 
> TAI8590 1-Wire Text User Interface
> 
> I have one and it works very nice; and includes
> provisions for switch
> closure detection.  It uses the DS2408 1-Wire 8-bit
> PIO.  So, you don't need
> ANY parallel I/O bits at all!
> 
> "Based on the Dallas Semiconductor DS2408 the
> TAI8590 1-Wire Text User
> Interface allow you to connect a LCD Character
> display to your 1-Wire
> network and recieve messages from the host system.
> Also included in the
> module is the capability to connect push buttons to
> allow you to interact
> with the host program on your system. This module is
> fully compatible with
> the rest of  TAI 1-Wire devices. Software to test
> the module and Java
> classes are available at no cost in our Download
> Area."
> 
> Best regards, Kelly Smith
> 
> -----Original Message-----
> From: tini-admin-6tN4nzCoH/[email protected]
> [mailto:tini-admin-6tN4nzCoH/[email protected]]On Behalf Of
> Jing Qiu
> Sent: Wednesday, March 10, 2004 10:08 AM
> To: tini-6tN4nzCoH/[email protected]
> Subject: Re: [TINI]How can I access the TINI IO
> Ports
> 
> 
> Thanks. I want to connect an LCD to the DSTINIs400
> socket, but as you said, there's only a few IO port
> pins available. I see there are 32 user parallel IO
> pins available. How to use these user PIOs to access
> the data/address/control BUS?
> 
>  --- Bryan Armstrong <bryan.armstrong-6tN4nzCoH/[email protected]>
> wrote: > Jing Qiu wrote:
> > > I'm using DSTINIs400 socket, could anybody show
> me
> > > where's the TINI IO ports, as I couldn't find
> them
> > on
> > > the datasheet.
> >
> > Look for pin names such as P0,P1,P2,P3,etc.  Some
> > ports are not
> > accessible as they are used for address/data/chip
> > enables.
> >
> > --
> > --
> > Bryan Armstrong
> > bryan.armstrong-6tN4nzCoH/[email protected]
> >
> >
> 
>
______________________________________________________________________
> Post your free ad now! http://personals.yahoo.ca
> _______________________________________________
> TINI mailing list
> TINI-6tN4nzCoH/[email protected]
> To UNSUBSCRIBE, edit your profile, or see list
> archives:
> http://lists.dalsemi.com/mailman/listinfo/tini
> 
> 
> _______________________________________________
> TINI mailing list
> TINI-6tN4nzCoH/[email protected]
> To UNSUBSCRIBE, edit your profile, or see list
> archives:
> http://lists.dalsemi.com/mailman/listinfo/tini
> 
> 
>  

______________________________________________________________________ 
Post your free ad now! http://personals.yahoo.ca
_______________________________________________
TINI mailing list
TINI-6tN4nzCoH/[email protected]
To UNSUBSCRIBE, edit your profile, or see list archives:
http://lists.dalsemi.com/mailman/listinfo/tini