RE: Telnet problem with TINI 400

Thx for your response, I appreciate it. I got the
problem resolved. I have a D-Link wireless router and
my PCs are connected to it in a home netwk. I conneted
the TINI directly on one of the PC with a crossover
cable. It seems that I had to change my settings on
the LAN card of my PC and give it a static IP and
default gateway as itself(and ofcourse the mask too of
255.255.255.0). I left the DNS settings blank(don't
know if that would be a problem). And, I could telnet
TINI from that PC. I think the IP address of TINI
which I gave before, 192.168.0.15, was colliding with
the DHCP on the D-Link. I also changed the IP address
of TINI to 192.168.1.20

But, I cannot reach TINI on this PC from any other
PCs, in the home network. I assigned a gateway IP to
TINI as the PC to which it is connected. Any ideas ??
--- Kelly Smith <[email protected]> wrote:
> Dear Vijay - Try pinging from your development PC
> and also another PC, using
> the DOS command prompt (from 'Start' -> 'Run', as:
> 
> ping 192.168.0.15 -t <-- the "-t" will cause ping to
> run "forever".
> 
> If one PC fails and the other does NOT, you can
> start chasing the problem in
> the "bad" PC; if they both fail, start chasing down
> the problem in your
> network.  If you have TWO IP address's at
> "192.168.0.15", this could cause a
> conflict.  If you have a hub on the system, check
> the "collision indicator";
> Maybe there is something in your network trying to
> do NAT (and confusing on
> the address translation?).
> 
> Your "NetMask" on all address's is "255.255.255.0"
> ???
> 
> Just some ideas for you to investigate... Best
> regards, Kelly
> 
> -----Original Message-----
> From: tini-admin-6tN4nzCoH/[email protected]
> [mailto:tini-admin-6tN4nzCoH/[email protected]]On Behalf Of
> Vijay Phagura
> Sent: Thursday, June 03, 2004 1:29 PM
> To: tini-6tN4nzCoH/[email protected]
> Subject: [TINI]Telnet problem with TINI 400
> 
> 
> Hi,
> 
> I cannot reach tini from my computer directly
> connected to it, via telnet. I have a crossover
> cable
> from my computer to the TINI and running Win 2000 on
> my computer. I have loaded the firmware etc from the
> serial port and that went fine and the JavaKit
> connection works also fine.
> 
> The telnet works when I try to disconnect the cord
> and
> reconnect it and try 'telnet 192.168.0.15' many
> times,
> from my computer. I get the tini login, after I
> login
> I can work on it and as I'm working, just after few
> secs it says 'connection lost' and kicks me back
> out.
> 
> Any help would be appreciated.
> 
> 
> 
> 
> 
> 
> __________________________________
> Do you Yahoo!?
> Friends.  Fun.  Try the all-new Yahoo! Messenger.
> http://messenger.yahoo.com/
> _______________________________________________
> TINI mailing list
> TINI-6tN4nzCoH/[email protected]
> To UNSUBSCRIBE, edit your profile, or see list
> archives:
> http://lists.dalsemi.com/mailman/listinfo/tini
> 
> 



	
		
__________________________________
Do you Yahoo!?
Friends.  Fun.  Try the all-new Yahoo! Messenger.
http://messenger.yahoo.com/ 
_______________________________________________
TINI mailing list
TINI-6tN4nzCoH/[email protected]
To UNSUBSCRIBE, edit your profile, or see list archives:
http://lists.dalsemi.com/mailman/listinfo/tini