回复： RE: How to use visionC lick to program MPC555 shadow and boot fro m internal flash?

Dear Dees,
     
        Thank you so much！
         I do have two REG files, one for programming the shadow and another for the Main flash. The diffrence of them is that in the former :CMFMCR_A   is 89FF00FF(SIE bit is 1 ) , and in the later : CMFMCR_A  is changed into 81FF00FF. But I still have some problems when operation in VisionClick to program the shadow.
formerly    the board would read the reset configuration word form the databus and when i programming, I just program the Main flash and in visionClick I just select the : MPC555 K1,2,3,M ( 448 x 8 ) 1 Device” Driver.
and all these do work.
 
But here I want the board would read the Shadow when rest or power on, so when I change the .reg file, and before programming the shadow, which driver should I select ? There is no such drivers just for shadow in my visionClick. 
 
another question is : how I get the special .bin(256 byte)
 file for the shadow? the visionclick have provide a example 256_shadow.bin ( please see the following) but 
it's more than 256 byte! More over, how I change this example for my application?
 yesterday you have provded me a sample code for shadow:S107000010000000E8, but I don't kown how to make it suit for the visionClick spesial .bin file style!
I think the first 32 bit in the shadow should be:0x1040 0000, that is : the bit 20 should be 0? Is it righ?
 
Thank you somuch!
Best regards!

Dees Randy-rsaf30 <[email protected]> 写道：
here is a simple Reset Config Word SRECORD that can be programmed into the shadow row by your tool:
S107000010000000E8

this enables the flash and disables external boot.

-----Original Message-----
From: [email protected] [mailto:[email protected]] On Behalf Of wupegasus
Subject: [MPC500] How to use visionClick to program MPC555 shadow and boot from internal flash?




[Non-text portions of this message have been removed]



-----------------------------------------------------------
To learn more about Freescale Microcontrollers, please visit
http://www.freescale.com/mcu






---------------------------------
YAHOO! GROUPS LINKS 


    Visit your group "MPC500" on the web.
  
    To unsubscribe from this group, send an email to:
 [email protected]
  
    Your use of Yahoo! Groups is subject to the Yahoo! Terms of Service. 


---------------------------------





		
---------------------------------
DO YOU YAHOO!?
  雅虎免费G邮箱－No.1的防毒防垃圾超大邮箱  

[Non-text portions of this message have been removed]



------------------------ Yahoo! Groups Sponsor --------------------~--> 
<font face=arial size=-1><a href="http://us.ard.yahoo.com/SIG=12h3uka1g/M=362131.6882499.7825260.1510227/D=groups/S=1706554205:TM/Y=YAHOO/EXP=1124549574/A=2889191/R=0/SIG=10r90krvo/*http://www.thebeehive.org
">Get Bzzzy! (real tools to help you find a job) Welcome to the Sweet Life -brought to you by One Economy</a>.</font>
--------------------------------------------------------------------~-> 

-----------------------------------------------------------
To learn more about Freescale Microcontrollers, please visit
http://www.freescale.com/mcu


 
Yahoo! Groups Links

<*> To visit your group on the web, go to:
    http://groups.yahoo.com/group/MPC500/

<*> To unsubscribe from this group, send an email to:
    [email protected]

<*> Your use of Yahoo! Groups is subject to:
    http://docs.yahoo.com/info/terms/