Re: using in-board ez430 FET emulator
Eric Decker <[email protected]>
| Newsgroups | gmane.comp.hardware.texas-instruments.msp430.gcc.user |
|---|---|
| Message-ID | <[email protected]> |
From cPhone On Jun 22, 2013, at 6:00 PM, John Willauer <[email protected]> wrote: > I am using Ubuntu Linux version 12.04 with: old stuff. I don't know why. I don't support that stuff some notes.... first until the Ubuntu repository gets sorted out use mine. http://tinyprod.net/repos/debian/ follow the README instructions more below > > mspdebug 0.18-1 old. I'm using 0.21 I do t know what the state of the rest of what you got is > db-msp430 7.2~mspgcc-7.2.2 > gcc-msp439 4.5.3~mspgcc-201 4.5.3 has known problems you should be using 4.6.3 > > The MSP430 development software was downloaded from: > > http://extras.ubuntu.com/ubuntu precise main #Third party developers repository > > I have developed several applications for the msp430g2553 but always got a Segment fault when I tried to use gdb. > > -- > John > - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - > > > On 06/22/2013 05:12 PM, Eric Decker wrote: >> >> What version of msp430-gdb are you running? Where did you get it? >> >> do.. >> >> dpkg -l "*msp430*" >> >> and how do you have apt configured? What repository are you using to get the tools from? >> >> >> >> On Sat, Jun 22, 2013 at 5:10 PM, John Willauer <[email protected]> wrote: >>> How do I eliminate the "Segmentation fault" that occurs when I start msp430-gdb using the following procedure Jose Luis Honorato described in his response to Ravim. >>> >>> When the msp430-gdb is started, in the second shell, a Segmentation fault is reported then the msp430-gdb terminates. >>> >>> I am trying to use gdb to debug code running on a Launchpad with a msp430g2553 chip. >>> >>> >>> -- >>> John >>> - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - >>> >>> On 06/22/2013 01:06 PM, Eric Decker wrote: >>>> >>>> Just asking how to get rid of a "seg fault" isn't to helpful. >>>> >>>> What program was actually running? What version? What address? >>>> >>>> >>>> On Sat, Jun 22, 2013 at 11:55 AM, John Willauer <[email protected]> wrote: >>>>> How do I eliminate the "Segmentation fault" I get when I try it using: >>>>> >>>>> Ubuntu 12.04 >>>>> mspdebug 0.18-1 >>>>> gdb-msp430 7.2~mspgcc-7.2.2 >>>>> gcc-msp439 4.5.3~mspgcc-201 >>>>> >>>>> -- >>>>> John >>>>> - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - >>>>> >>>>> >>>>> >>>>> On 06/20/2013 09:53 AM, Jose Luis Honorato L. wrote: >>>>>> Hi Ravim, >>>>>> >>>>>> I can't see the output messages you intended to include, but here's a short >>>>>> how-to. I just hope you don't have a specific problem with your setup. >>>>>> >>>>>> You can use the ez430-FET emulator to program the msp-exp430f5529 without >>>>>> any external hardware. Just plug your mini USB cable to the lower left USB >>>>>> connector (the one in the ez430-FET emulator) and run: >>>>>> >>>>>> sudo mspdebug rf2500 "prog bin.elf" >>>>>> >>>>>> That should program the device after a few console messages. >>>>>> >>>>>> You can use mspdebug with gdb too, for that you should: >>>>>> >>>>>> 1. Run mspdebug (sudo mspdebug rf2500) >>>>>> 2. In mspdebug, type gdb >>>>>> 3. In another window, run msp430-gdb >>>>>> 4. In gdb, type target remote localhost:2000 >>>>>> 5. Done >>>>>> >>>>>> This is assuming you have all these tools installed, if not there are >>>>>> plenty of guides out there on how to install them. >>>>>> >>>>>> Kind regards, >>>>>> Jose >>>>>> _______________________________________________ >>>>>> Mspgcc-users mailing list >>>>>> [email protected] >>>>>> https://lists.sourceforge.net/lists/listinfo/mspgcc-users >>>>> >>>>> ------------------------------------------------------------------------------ >>>>> This SF.net email is sponsored by Windows: >>>>> >>>>> Build for Windows Store. >>>>> >>>>> http://p.sf.net/sfu/windows-dev2dev >>>>> _______________________________________________ >>>>> Mspgcc-users mailing list >>>>> [email protected] >>>>> https://lists.sourceforge.net/lists/listinfo/mspgcc-users >>>>> >>>> -- >>>> Eric B. Decker >>>> Senior (over 50 :-) Researcher >>>> >>> >> >> >> >> -- >> Eric B. Decker >> Senior (over 50 :-) Researcher >> > ------------------------------------------------------------------------------ This SF.net email is sponsored by Windows: Build for Windows Store. http://p.sf.net/sfu/windows-dev2dev _______________________________________________ Mspgcc-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/mspgcc-users