Argosy Netdisk

saw some of y'all on here wondering about the argosy hd 363N enclosure. it
is deefinitely an nas device and it does really well. It also runs a telnet
server. here is output of sys and help command below. Just use putty or
somehting and use the same admin and pass you configure through web.

ARGOSY NET Disk,Telnet Server [release 2.0]
ARGOSY>sys
Host Name:ARGOSY NET Disk  Firmware:ARGOSY029-1103
Hardware Version : 001E Speed 125Mhz
Timers: 12 In use, 8 free
RTC enable
Primary DNS 205.152.37.23  Secondary DNS 192.168.1.1
System time: 2005/2/6 11:24:0
log file C:\LOG.TXT, maximum length 5316608, log function on
Debug level 1
ARGOSY>help
sys        -h (help), -d (debug level), -p (performance), -s (services)
        debug <level> (0:disable, 1-5 debug level)
        save (save system configuration)
        reload (reload system default configuration)
        [forward | nat | dod | clone | dnspxy | upnp | multi | rip
                 | fire | pptp | ids]
                (enable or disable specificed function)
        prompt <string> (Set the prompt string for shell)
        user (list system's users, maximum 3 users
        add <username> <password> (add a user)
        del <username> (delete a user)
        reboot (system restart)
        date YY/MM/DD (system date)
        time HH:MM:SS [12/24][am/pm](system time,
                12 or 24 hour mode, default is 24)
        log (display syslog configuration)
           [on | off] (turn on/of log function)
           length <file length>

mem        r [bw] address <data>
        w [bw] address <data>
        f [bw] address <length> <data>
        d [bw] address <length>
        t address <data> <length>
config     host <name string> (program host name
        mac <port> <MAC address>
        ip <IP adress> mask <net mask> gw <gateway address> (LAN side)
        pool <start> <end> (DHCP Server Pool range (1-253)
        wins <IP address> (WINS Server address)
        service <name string> (program PPP service name
        dod <enable/disable> (PPP dial on demand enable or disable)
        idle <time (seconds)> (PPP idle time, 0 means always on)
        dns <0/1> <address> (DNS server address, 0 primary, 1 secondary
        http <port> (embedded HTTP server port)
        ping <enable/disable> (enable or disable ping from WAN)
        remote <enable/disable> (enable or disable remote management from WAN
        save (save vendor configuration)
        reload (remove vendor configuration)
        (display vendor default configuration)
help       [command]
device     -h (help)
        [device name][mac | clone | multi <MAC address>] [normal | promiscuous][
on | off]
        [up][Down]
        [device name][9600/19200/38400/57600/115200][none/odd/even]
        [data <6/7/8>][stop <1/2>][up][Down]
        debug <level> (0:disable, 1-5 debug level)
        save
        reload
dir
write      [-f] [-l maxlen] [-p position] <file> [<data>]
type       [-a | -b] <file>
cat        <dest file> [<source file> | data string]
del        <file> [<files>]
cp         [-f -l max length] <source file> <destination file>
cd         <directory name>
md         <old folder name>, <new folder name>
rd         <folder name>
pwd
pci
flash      erase [<all> | <start address> <end address> |
                <start sector> <end sector>]
        write <start address> [<file name> | <data string>]
        info
if         -h (help)
        -a (list all interfaces)
        <interface name> [<ip | mask | gw> <ip address>] [mtu <valus>]
        [none | dhcp | ppp (for PPP interface)] [name (new interface name)]
        [up | down][clear (counters)]
        add <interface name> <physical device (or bridge or PPP)>
        del <interface name>
        debug <level> (0:disable, 1-5 debug level)
        save
        reload

ping       <dest ip addreess> [-s size] [-c count]
route      add <dest ip> <mask> <gateway> <0-15>(metric) <dev>
        del <dest ip>
        save
        reload
        debug <level> (0:disable, 1-5 debug level)
arp        add <IP address> <MAC address> <interface name>
        del <IP address>
        flush
        req <IP address> <netif name> [<timer(1-4)>]
tcpip      -h(help),-s(socket info),-u(user info), -p(pcb info)
        cksum [on|off](turn on or turn off calculate receive checksum
        debug <level> (0:disable, 1-5 debug level)
        show
io         [r|w] <address> [<data> | <length> (for read)]
dhcps      save (save the DHCP server's configuration)
        reload (the DHCP server's configuration)
        debug <level>(0:disable, 1-5 debug level)
        <interface name>
        [interface name] lease offered <START IP> <NUMBER>
        [interface name] lease fix <START IP> <NUMBER>
        [interface name] lease offering <START IP> <NUMBER>
        [interface name] lease record <START IP> <NUMBER>
        [interface name] up
        [interface name] down
        [interface name] flush
        [interface name] dns1 <DNS IP> dns2 <DNS IP>
        [interface name] router <Router IP>
        [interface name] wins <WINS IP>
        [interface name] pool <min> <max>
        [interface name] leasetime <day> <hour> <minute>
        [interface name] add <MAC> <IP> <HOSTNAME>
        [interface name] del <IP>
        [interface name] probe [ON]|[OFF]
dhcpc      debug <level>(0:disable, 1-5 debug level)
        debug_test (0:disable, 1-2 debug level)
        <interface name> renew
        <interface name> rebind
sntpc      [-t timezone(hour)][-d debug level][-h help]
        save (save the configuration)
        restore (restore the original configuration)
        server [ip addreess] (Set SNTP Server IP address)
        [on|off] (active/deactive SNTP client to get current time)

dnsproxy   debug <level>        (0:disable, 1-5 debug level)
                [open/close]    (open/close Dns Proxy function)
                [on/off]        (Enable/disable Dns Proxy cache)
                cache           (dump all cache information)
                dump <node #>   (dump cache information at node #)
                clear           (clear all cache data)
                delete <node #> (clear cache data at node #)
                limit <size>    (set limit size of cache node count)
                expire <sec>    (set expired time in sec)
                ns <domain>     (nslookup domain name's ip)

ide        debug <level>                (0:disable, 1-5 debug level)
        sleep <partition>       (Sleep mode in <partition>)
        idle <min>              (set min for Sleep mode)
        wait <T1> <T3>          (set PIO T1 & T3 wait states )
        device <0~3>, part<#>   (Set device number, partition number)
        lba <sector>            (Set read sector's lba)
        r <sector> <counts>             (Read sector (or for counts))
        rc <cluster> (for counts)       (Read cluster)
        w0 <lba> (for counts)   (clear sectors with data 0)
        rewrtsec <lba>          (Re-write sectors)
        buffer <bytes>          (set file read/write buffer size)
        edit <off> <data>       (edit data in sector:offset)

        ident <device>          (Get identify of device)
        boot <dev> <part>       (Get boot information <device> <partitition>)
        initdisk <dev> <K>      (create one partition as <K> cluster)
        fdisk           (fdisk utility)
        format <PartName> <K>   (format <partitition name> as <K> cluster)
        formatq <PartName>      (quick format <partitition name>)

        dir
        pwd                     (Print working directory)
        cd, md, rd<dir_name>    (Change, Make, Remove directory)

        del, ren <file_name>            (delete/rename filename)
        copy <srcfile destfile> (copy source file to dest file)
        move <srcfile destfile> (move source file to dest file(full path))
        cchain <cluster>        (get all the cluster links from <cluster>
        readf <file_name>       (only read file, for test)

mount      <IDE device> <partition ID> <mount point>
umount     <mount point>
ftps       .    (display FTP server's status
        save/reload     (save/reload the FTP server's configuration
        debug <level>   (0:disable, 1-5 debug level)
        service [on|off]        (Enable/disable FTP server)
        add <username> <password> [<home>]      (add a new user)
        del <username>  (delete an existing user)
        pass <username> <old password> <new password>
                (change password of existing user)
        home <username> <new home dir>
        user <username> [on|off]        (enable/disable FTP server's user)
        check <username> [on|off]       (check password?)
        attrib <username> [ro|rw        (read only or read write)
        addshare <username> <dir no> (e.g. >ftp addshare rdc 1)
        delshare <username> <dir no> (e.g. >ftp delshare rdc 1)
        togshare <username> <dir no> (e.g. >ftp togshare rdc 1)
        list (list existing user)
        share <username> (toggle user to home or share mode)

ftp        ftp <ftp site URL or IP address>
smb        -h (help)
        save (save config for next system boot)
        debug <level>  level
        name <smb's name> max 14 characters
        group <group's name> max 14 characters
        root <ide id>, e.g C: or D1:
        [on|off] enable or disable the smb function

nas        -h (help)
        save (save config for next system boot)
        new <directory> create new sharing dir
        del <directory> delete old sharing dir
        rename <oldname> <newname> rename sharing dir
        pass <directory> <password> set password to dir
        pass <directory> disable password attached to dir

http       debug <level> (0:disable, 1-5 debug level)
        ip <ip address> (client ip, 0 is for any client)
        port <port> (listen port, work after reboot)
        save (save config to flash)