Re: problem with new install on new Centos 7.5 system

Zitat von Edward Burr <[email protected]>:

> Quoting Ralf Lang <[email protected]>:
>
>> Am 14.11.18 um 19:21 schrieb Edward Burr:
>>> Hi Ralf,
>>>
>>> Thanks for the suggestion. 'yum install php-http' installed
>>> php-pecl-http and now "pecl list" shows pecl_http is installed. So,
>>> the step 2.5 issue appears to be cleared up?
>>>
>>> But the step 3.1 and 3.3 issues remain.
>>>
>>> 3.1) During "pear install -a horde/groupware":
>>> Failed to download horde/Horde_Backup within preferred state "stable",
>>> latest release is version 1.0.0RC1, stability "beta", use
>>> "channel://pear.horde.org/Horde_Backup-1.0.0RC1" to install
>>> Failed to download pecl/sasl within preferred state "stable", latest
>>> release is version 0.1.0, stability "alpha", use
>>> "channel://pecl.php.net/sasl-0.1.0" to install
>>> Failed to download pecl/idn within preferred state "stable", latest
>>> release is version 0.2.0, stability "beta", use
>>> "channel://pecl.php.net/idn-0.2.0" to install
>>>
>>> Trying to install each manually fails.
>>>
>> If you are using distribution php, get the PECLs from distribution (yum).
>>
>> For installing RC packages, either preinstall Horde_Backup ignoring deps
>> (pear install -n horde/Horde_Backup) or allow installation of beta software
>>
>> |pear config-setpreferred_state beta|
>>
>> change to stable when you are done.
>>
>
> yum install php-sasl
> yum install pecl-sasl
> yum install pecl_sasl
> yum install pear-sasl
> yum install pear_sasl
> # All result in "No package XXX available. Nothing to do."
>
> yum install php-idn
> # installed php-idn-1.2c-12
>
> pecl install channel://pecl.php.net/idn-0.2.0
> # still fails with same error
>
> I uninstalled all the horde packages and pre-installed Horde_Backup  
> per your suggestion.
>
> pear uninstall `pear list -c horde | tail -n +4 | awk '{ print "horde/"$1 }'`
> pear install -n horde/Horde_Backup-1.0.0RC1
> install ok: channel://pear.horde.org/Horde_Backup-1.0.0RC1
>
> Then installed horde:
> pear install horde/horde_role
> pear run-scripts horde/horde_role
> pear install -a horde/groupware
>
> But Horde_Core failed to install, and many components depending on  
> Horde_Core:
> horde/Horde_Core requires package "horde/Horde_Backup" (version >=  
> 1.0.0, version <= 2.0.0alpha1, excluded versions: 2.0.0alpha1),  
> installed version is 1.0.0RC1
>
> ASpparently 1.0.0RC1 isn't greater than/equal to 1.0.0 even though  
> that's apparently the absolute latest available:
> Failed to download horde/Horde_Backup within preferred state  
> "stable", latest release is version 1.0.0RC1, stability "beta", use  
> "channel://pear.horde.org/Horde_Backup-1.0.0RC1" to install
>
> How do I satisfy this requirement?
>
> The install directions appear pretty straightforward. I've got to be  
> missing something obvious, but I can't figure out what it could be.

pear install horde/horde_backup-beta

-- 
Jan Schneider
The Horde Project
https://www.horde.org/

-- 
Horde mailing list
Frequently Asked Questions: http://horde.org/faq/
To unsubscribe, mail: [email protected]