Re: problem with new install on new Centos 7.5 system

Quoting Jan Schneider <[email protected]>:

> Zitat von Edward Burr <[email protected]>:
>
>> Quoting Ralf Lang <[email protected]>:
>>
>>> Am 14.11.18 um 19:21 schrieb Edward Burr:
>>>> Hi Ralf,
>>>>
>>>> Thanks for the suggestion. 'yum install php-http' installed
>>>> php-pecl-http and now "pecl list" shows pecl_http is installed. So,
>>>> the step 2.5 issue appears to be cleared up?
>>>>
>>>> But the step 3.1 and 3.3 issues remain.
>>>>
>>>> 3.1) During "pear install -a horde/groupware":
>>>> Failed to download horde/Horde_Backup within preferred state "stable",
>>>> latest release is version 1.0.0RC1, stability "beta", use
>>>> "channel://pear.horde.org/Horde_Backup-1.0.0RC1" to install
>>>> Failed to download pecl/sasl within preferred state "stable", latest
>>>> release is version 0.1.0, stability "alpha", use
>>>> "channel://pecl.php.net/sasl-0.1.0" to install
>>>> Failed to download pecl/idn within preferred state "stable", latest
>>>> release is version 0.2.0, stability "beta", use
>>>> "channel://pecl.php.net/idn-0.2.0" to install
>>>>
>>>> Trying to install each manually fails.
>>>>
>>> If you are using distribution php, get the PECLs from distribution (yum).
>>>
>>> For installing RC packages, either preinstall Horde_Backup ignoring deps
>>> (pear install -n horde/Horde_Backup) or allow installation of beta software
>>>
>>> |pear config-setpreferred_state beta|
>>>
>>> change to stable when you are done.
>>>
>>
>> yum install php-sasl
>> yum install pecl-sasl
>> yum install pecl_sasl
>> yum install pear-sasl
>> yum install pear_sasl
>> # All result in "No package XXX available. Nothing to do."
>>
>> yum install php-idn
>> # installed php-idn-1.2c-12
>>
>> pecl install channel://pecl.php.net/idn-0.2.0
>> # still fails with same error
>>
>> I uninstalled all the horde packages and pre-installed Horde_Backup  
>> per your suggestion.
>>
>> pear uninstall `pear list -c horde | tail -n +4 | awk '{ print  
>> "horde/"$1 }'`
>> pear install -n horde/Horde_Backup-1.0.0RC1
>> install ok: channel://pear.horde.org/Horde_Backup-1.0.0RC1
>>
>> Then installed horde:
>> pear install horde/horde_role
>> pear run-scripts horde/horde_role
>> pear install -a horde/groupware
>>
>> But Horde_Core failed to install, and many components depending on  
>> Horde_Core:
>> horde/Horde_Core requires package "horde/Horde_Backup" (version >=  
>> 1.0.0, version <= 2.0.0alpha1, excluded versions: 2.0.0alpha1),  
>> installed version is 1.0.0RC1
>>
>> ASpparently 1.0.0RC1 isn't greater than/equal to 1.0.0 even though  
>> that's apparently the absolute latest available:
>> Failed to download horde/Horde_Backup within preferred state  
>> "stable", latest release is version 1.0.0RC1, stability "beta", use  
>> "channel://pear.horde.org/Horde_Backup-1.0.0RC1" to install
>>
>> How do I satisfy this requirement?
>>
>> The install directions appear pretty straightforward. I've got to  
>> be missing something obvious, but I can't figure out what it could  
>> be.
>
> pear install horde/horde_backup-beta

Among other things, that did:
downloading Horde_Backup-1.0.0RC1.tgz ...
Starting to download Horde_Backup-1.0.0RC1.tgz (8,518 bytes)
.....done: 8,518 bytes
install ok: channel://pear.horde.org/Horde_Backup-1.0.0RC1

which leaves us still with the same problem as above.


>
> -- 
> Jan Schneider
> The Horde Project
> https://www.horde.org/
>
> -- 
> Horde mailing list
> Frequently Asked Questions: http://horde.org/faq/
> To unsubscribe, mail: [email protected]

-- 
Horde mailing list
Frequently Asked Questions: http://horde.org/faq/
To unsubscribe, mail: [email protected]