Re: [mh] Insteon problems with new PLM

I have experienced what sounds similar with KeyPadLink units, found I 
had to factory reset to get them to behave and respond properly.

On 10/16/19 4:03 PM, Seann via misterhouse-users wrote:
> All,
> I recently replaced my old, and issue prone PLM (2412S V3.1) with a 
> new model, a 2413s. While running into issues that I have seen on the 
> mailing list and forums before, mainly with having to manually re-link 
> devices with the PLM, I came across an error that I can't find any 
> data on.
> Two of my lamplinc devices refused to sync or link (manual linking 
> doesn't seem to take either, have tried it two times each way, via 
> link as controller in MH, and by manually on the PLM via the set 
> button), and return the error "pre_nak_long_db_search" as part of the 
> NACK sent back.  I can't find anything at all on google for this 
> specific message, so I am stumped and wondering if anyone else has 
> seen this?
> The other issue I have run into is I have a Keypadlinc that is 
> refusing to sync/link, but unlike the lamplinc's it doesn't return an 
> actual NAK message, it just blankly NACK's anything from the new PLM, 
> even after a factory reset.
>
> I am running the latest master branch code, and aside from dropped 
> messages and table errors on the old PLM, things were working very 
> well on my issue devices mentioned above.
>
>
> The logs for this, on debug are:
> 10/16/19 14:38:50  [Scan all link tables] Now scanning: 
> $Ceiling_fan_light (3 of 15)
> 10/16/19 14:38:50  [Insteon::AllLinkDatabase] WARN The link table for 
> $Ceiling_fan_light has changed.
> 10/16/19 14:38:50  [Insteon::ALDB_i2] $Ceiling_fan_light reading ALDB 
> at location: 0x0000
> 10/16/19 14:38:50  [Insteon::BaseObject] WARN!! encountered a nack 
> message () for $Ceiling_fan_light.  It may be unplugged, have a burned 
> out bulb, or this may be a new I2CS type device that must first be 
> manually linked to the PLM using the set button.
> 10/16/19 14:38:50  [Insteon::BaseObject] WARN: Now calling message 
> failure callback: &Insteon::_get_next_linkscan_failure(1)
> 10/16/19 14:38:50  [Scan all link tables] WARN: failure occurred when 
> scanning $Ceiling_fan_light.  Moving on...
> 10/16/19 14:38:50  [Scan all link tables] Now scanning: 
> $Left_Nightstand (4 of 15)
> 10/16/19 14:38:50  [Insteon::AllLinkDatabase] WARN The link table for 
> $Left_Nightstand has changed.
> 10/16/19 14:38:50  [Insteon::ALDB_i2] $Left_Nightstand reading ALDB at 
> location: 0x0000
> 10/16/19 14:38:51  [Insteon::BaseInterface] DEBUG: PLM 
> command:insteon_ext_received; Device command:read_write_aldb; 
> type:direct; group:
> 10/16/19 14:38:52  [Insteon::BaseObject] WARN!! encountered a nack 
> message (pre_nak_long_db_search) for $Left_Nightstand.  It may be 
> unplugged, have a burned out bulb, or this may be a new I2CS type 
> device that must first be manually linked to the PLM using the set 
> button.
> 10/16/19 14:38:52  [Insteon::BaseObject] WARN: Now calling message 
> failure callback: &Insteon::_get_next_linkscan_failure(1)
> 10/16/19 14:38:52  [Scan all link tables] WARN: failure occurred when 
> scanning $Left_Nightstand.  Moving on...
> 10/16/19 14:38:52  [Scan all link tables] Now scanning: 
> $Right_Nightstand (5 of 15)
> 10/16/19 14:38:52  [Insteon::AllLinkDatabase] WARN The link table for 
> $Right_Nightstand has changed.
> 10/16/19 14:38:52  [Insteon::ALDB_i2] $Right_Nightstand reading ALDB 
> at location: 0x0000
> 10/16/19 14:38:52  [Insteon::BaseInterface] DEBUG: PLM 
> command:insteon_ext_received; Device command:read_write_aldb; 
> type:direct; group:
> 10/16/19 14:38:53  [Insteon::BaseObject] WARN!! encountered a nack 
> message (pre_nak_long_db_search) for $Right_Nightstand.  It may be 
> unplugged, have a burned out bulb, or this may be a new I2CS type 
> device that must first be manually linked to the PLM using the set 
> button.
> 10/16/19 14:38:53  [Insteon::BaseObject] WARN: Now calling message 
> failure callback: &Insteon::_get_next_linkscan_failure(1)
> 10/16/19 14:38:53  [Scan all link tables] WARN: failure occurred when 
> scanning $Right_Nightstand.  Moving on...
>
> Has anyone seen, and come up with a resolution on this?
>
> Regards,
> Seann
>
>
>
>
>
>
> ________________________________________________________
> To unsubscribe from this list, go to: 
> https://lists.sourceforge.net/lists/listinfo/misterhouse-users
>



________________________________________________________
To unsubscribe from this list, go to: https://lists.sourceforge.net/lists/listinfo/misterhouse-users