Re: [mh] Insteon problems with new PLM

Off topic but is there a simple answer on how to install Win32::Setupsup for the current version of Active Perl or Strawberry Perl? CPAN has compile errors.
Thanks.
On 10/16/2019 4:31 PM, Spencer Ryan wrote:
Yeah, factory reset it again, and assuming your devices are i2cs all you should have to do is "link to interface"

On Wed, Oct 16, 2019, 5:30 PM Carl McGrath <[email protected]<mailto:[email protected]>> wrote:
I have experienced what sounds similar with KeyPadLink units, found I
had to factory reset to get them to behave and respond properly.

On 10/16/19 4:03 PM, Seann via misterhouse-users wrote:
> All,
> I recently replaced my old, and issue prone PLM (2412S V3.1) with a
> new model, a 2413s. While running into issues that I have seen on the
> mailing list and forums before, mainly with having to manually re-link
> devices with the PLM, I came across an error that I can't find any
> data on.
> Two of my lamplinc devices refused to sync or link (manual linking
> doesn't seem to take either, have tried it two times each way, via
> link as controller in MH, and by manually on the PLM via the set
> button), and return the error "pre_nak_long_db_search" as part of the
> NACK sent back.  I can't find anything at all on google for this
> specific message, so I am stumped and wondering if anyone else has
> seen this?
> The other issue I have run into is I have a Keypadlinc that is
> refusing to sync/link, but unlike the lamplinc's it doesn't return an
> actual NAK message, it just blankly NACK's anything from the new PLM,
> even after a factory reset.
>
> I am running the latest master branch code, and aside from dropped
> messages and table errors on the old PLM, things were working very
> well on my issue devices mentioned above.
>
>
> The logs for this, on debug are:
> 10/16/19 14:38:50  [Scan all link tables] Now scanning:
> $Ceiling_fan_light (3 of 15)
> 10/16/19 14:38:50  [Insteon::AllLinkDatabase] WARN The link table for
> $Ceiling_fan_light has changed.
> 10/16/19 14:38:50  [Insteon::ALDB_i2] $Ceiling_fan_light reading ALDB
> at location: 0x0000
> 10/16/19 14:38:50  [Insteon::BaseObject] WARN!! encountered a nack
> message () for $Ceiling_fan_light.  It may be unplugged, have a burned
> out bulb, or this may be a new I2CS type device that must first be
> manually linked to the PLM using the set button.
> 10/16/19 14:38:50  [Insteon::BaseObject] WARN: Now calling message
> failure callback: &Insteon::_get_next_linkscan_failure(1)
> 10/16/19 14:38:50  [Scan all link tables] WARN: failure occurred when
> scanning $Ceiling_fan_light.  Moving on...
> 10/16/19 14:38:50  [Scan all link tables] Now scanning:
> $Left_Nightstand (4 of 15)
> 10/16/19 14:38:50  [Insteon::AllLinkDatabase] WARN The link table for
> $Left_Nightstand has changed.
> 10/16/19 14:38:50  [Insteon::ALDB_i2] $Left_Nightstand reading ALDB at
> location: 0x0000
> 10/16/19 14:38:51  [Insteon::BaseInterface] DEBUG: PLM
> command:insteon_ext_received; Device command:read_write_aldb;
> type:direct; group:
> 10/16/19 14:38:52  [Insteon::BaseObject] WARN!! encountered a nack
> message (pre_nak_long_db_search) for $Left_Nightstand.  It may be
> unplugged, have a burned out bulb, or this may be a new I2CS type
> device that must first be manually linked to the PLM using the set
> button.
> 10/16/19 14:38:52  [Insteon::BaseObject] WARN: Now calling message
> failure callback: &Insteon::_get_next_linkscan_failure(1)
> 10/16/19 14:38:52  [Scan all link tables] WARN: failure occurred when
> scanning $Left_Nightstand.  Moving on...
> 10/16/19 14:38:52  [Scan all link tables] Now scanning:
> $Right_Nightstand (5 of 15)
> 10/16/19 14:38:52  [Insteon::AllLinkDatabase] WARN The link table for
> $Right_Nightstand has changed.
> 10/16/19 14:38:52  [Insteon::ALDB_i2] $Right_Nightstand reading ALDB
> at location: 0x0000
> 10/16/19 14:38:52  [Insteon::BaseInterface] DEBUG: PLM
> command:insteon_ext_received; Device command:read_write_aldb;
> type:direct; group:
> 10/16/19 14:38:53  [Insteon::BaseObject] WARN!! encountered a nack
> message (pre_nak_long_db_search) for $Right_Nightstand.  It may be
> unplugged, have a burned out bulb, or this may be a new I2CS type
> device that must first be manually linked to the PLM using the set
> button.
> 10/16/19 14:38:53  [Insteon::BaseObject] WARN: Now calling message
> failure callback: &Insteon::_get_next_linkscan_failure(1)
> 10/16/19 14:38:53  [Scan all link tables] WARN: failure occurred when
> scanning $Right_Nightstand.  Moving on...
>
> Has anyone seen, and come up with a resolution on this?
>
> Regards,
> Seann
>
>
>
>
>
>
> ________________________________________________________
> To unsubscribe from this list, go to:
> https://lists.sourceforge.net/lists/listinfo/misterhouse-users<https://urldefense.proofpoint.com/v2/url?u=https-3A__lists.sourceforge.net_lists_listinfo_misterhouse-2Dusers&d=DwMFaQ&c=gRgGjJ3BkIsb5y6s49QqsA&r=0AZapnbd99a1NB2emzVyYg&m=YZ3BJ-7pIRgDpsAE2dsrKDyOuLMedP3YiCR4r_5VAms&s=h1F2sdaFnNWpa9RYbSduZ6tCOTV92U0AJsE303SlKG0&e=>
>



________________________________________________________
To unsubscribe from this list, go to: https://lists.sourceforge.net/lists/listinfo/misterhouse-users<https://urldefense.proofpoint.com/v2/url?u=https-3A__lists.sourceforge.net_lists_listinfo_misterhouse-2Dusers&d=DwMFaQ&c=gRgGjJ3BkIsb5y6s49QqsA&r=0AZapnbd99a1NB2emzVyYg&m=YZ3BJ-7pIRgDpsAE2dsrKDyOuLMedP3YiCR4r_5VAms&s=h1F2sdaFnNWpa9RYbSduZ6tCOTV92U0AJsE303SlKG0&e=>





________________________________________________________
To unsubscribe from this list, go to: https://urldefense.proofpoint.com/v2/url?u=https-3A__lists.sourceforge.net_lists_listinfo_misterhouse-2Dusers&d=DwICAg&c=gRgGjJ3BkIsb5y6s49QqsA&r=0AZapnbd99a1NB2emzVyYg&m=YZ3BJ-7pIRgDpsAE2dsrKDyOuLMedP3YiCR4r_5VAms&s=h1F2sdaFnNWpa9RYbSduZ6tCOTV92U0AJsE303SlKG0&e=

________________________________________________________
To unsubscribe from this list, go to: https://lists.sourceforge.net/lists/listinfo/misterhouse-users