Re: ERROR: SMPP[xxxx]: got DLR but could not find message or was not interested in it

Manesh,

See msg-id-type in the User Guide. Also I suggest you to enable debug mode
to smsc group (log_level=0) to see how your provider work with a message ID
numbers.

--
Regards,
Denis

пт, 3 авг. 2018 г. в 9:38, mahesh Lavanam <[email protected]>:

> Hi,
>
> Please help me in resolving the DLR issue
>
> I have a SMS Port with 2 TX & 2 RX sessions enabled.
>
> I have configured these sessions in two kannel configurations with same
> smsc id
>
> *kannel1.conf - 1TX & 1RX(SMSbox1 & Bearerbox1) *
>
> #1st tx connection
> group = smsc
> smsc = smpp
> smsc-id = tran
> host = xxx.xxx.xxx.xx
> port = xxx
> smsc-username = xxxxx
> smsc-password = xxxxxx
> system-type = smpp
> connect-allow-ip = 127.0.0.1
> source-addr-ton = 0
> source-addr-npi = 1
> dest-addr-ton = 1
> dest-addr-npi = 1
>
>
> #1st Rx Connection
> group = smsc
> smsc = smpp
> smsc-id = tran
> host = xxx.xxx.xxx.xx
> port = xxx
> smsc-username = xxxxx
> smsc-password = xxxxxx
> system-type = smpp
> connect-allow-ip = 127.0.0.1
> source-addr-ton = 0
> source-addr-npi = 1
> dest-addr-ton = 1
> dest-addr-npi = 1
>
> kannel2.conf * - 1TX & 1RX(SMSbox2 & Bearerbox2) *
>
> #1st tx connection
> group = smsc
> smsc = smpp
> smsc-id = tran
> host = xxx.xxx.xxx.xx
> port = xxx
> smsc-username = xxxxx
> smsc-password = xxxxxx
> system-type = smpp
> connect-allow-ip = 127.0.0.1
> source-addr-ton = 0
> source-addr-npi = 1
> dest-addr-ton = 1
> dest-addr-npi = 1
>
>
> #1st Rx Connection
> group = smsc
> smsc = smpp
> smsc-id = tran
> host = xxx.xxx.xxx.xx
> port = xxx
> smsc-username = xxxxx
> smsc-password = xxxxxx
> system-type = smpp
> connect-allow-ip = 127.0.0.1
> source-addr-ton = 0
> source-addr-npi = 1
> dest-addr-ton = 1
> dest-addr-npi = 1
>
>
> In kannel2.log file, I see that kannel1's sms DLRs are receiving and
> seeing the error as below:
>
> DEBUG: DLR[internal]: Looking for DLR smsc=tran, ts=0160683811,
> dst=919134556661, type=1
> WARNING: DLR[internal]: DLR from SMSC<tran> for DST<919134556661> not
> found.
> ERROR: SMPP[bsnl_tran]: got DLR but could not find message or was not
> interested in it id<0160683811> dst<919134556661>, type<1>
>
> Same error at kannel1.log file, when received the SMS DLRs of kannel2's
> messages
>
> Please help me to resolve the issue, to route the DLRs into its respective
> kannel's i.e., Kannel1's sent sms dlr into kannel1 & kannel2's sent sms dlr
> into kannel2.
>
> Thanks,
> Mahesh
>
>