Re: ERROR: SMPP[xxxx]: got DLR but could not find message or was not interested in it

Thank you all. It worked with the DLR Storage in same database.


- Mahesh

On Sat, Aug 4, 2018 at 12:56 PM, Денис Давыдов <[email protected]> wrote:

> Manesh,
>
> See msg-id-type in the User Guide. Also I suggest you to enable debug mode
> to smsc group (log_level=0) to see how your provider work with a message ID
> numbers.
>
> --
> Regards,
> Denis
>
> пт, 3 авг. 2018 г. в 9:38, mahesh Lavanam <[email protected]>:
>
>> Hi,
>>
>> Please help me in resolving the DLR issue
>>
>> I have a SMS Port with 2 TX & 2 RX sessions enabled.
>>
>> I have configured these sessions in two kannel configurations with same
>> smsc id
>>
>> *kannel1.conf - 1TX & 1RX(SMSbox1 & Bearerbox1) *
>>
>> #1st tx connection
>> group = smsc
>> smsc = smpp
>> smsc-id = tran
>> host = xxx.xxx.xxx.xx
>> port = xxx
>> smsc-username = xxxxx
>> smsc-password = xxxxxx
>> system-type = smpp
>> connect-allow-ip = 127.0.0.1
>> source-addr-ton = 0
>> source-addr-npi = 1
>> dest-addr-ton = 1
>> dest-addr-npi = 1
>>
>>
>> #1st Rx Connection
>> group = smsc
>> smsc = smpp
>> smsc-id = tran
>> host = xxx.xxx.xxx.xx
>> port = xxx
>> smsc-username = xxxxx
>> smsc-password = xxxxxx
>> system-type = smpp
>> connect-allow-ip = 127.0.0.1
>> source-addr-ton = 0
>> source-addr-npi = 1
>> dest-addr-ton = 1
>> dest-addr-npi = 1
>>
>> kannel2.conf * - 1TX & 1RX(SMSbox2 & Bearerbox2) *
>>
>> #1st tx connection
>> group = smsc
>> smsc = smpp
>> smsc-id = tran
>> host = xxx.xxx.xxx.xx
>> port = xxx
>> smsc-username = xxxxx
>> smsc-password = xxxxxx
>> system-type = smpp
>> connect-allow-ip = 127.0.0.1
>> source-addr-ton = 0
>> source-addr-npi = 1
>> dest-addr-ton = 1
>> dest-addr-npi = 1
>>
>>
>> #1st Rx Connection
>> group = smsc
>> smsc = smpp
>> smsc-id = tran
>> host = xxx.xxx.xxx.xx
>> port = xxx
>> smsc-username = xxxxx
>> smsc-password = xxxxxx
>> system-type = smpp
>> connect-allow-ip = 127.0.0.1
>> source-addr-ton = 0
>> source-addr-npi = 1
>> dest-addr-ton = 1
>> dest-addr-npi = 1
>>
>>
>> In kannel2.log file, I see that kannel1's sms DLRs are receiving and
>> seeing the error as below:
>>
>> DEBUG: DLR[internal]: Looking for DLR smsc=tran, ts=0160683811,
>> dst=919134556661, type=1
>> WARNING: DLR[internal]: DLR from SMSC<tran> for DST<919134556661> not
>> found.
>> ERROR: SMPP[bsnl_tran]: got DLR but could not find message or was not
>> interested in it id<0160683811> dst<919134556661>, type<1>
>>
>> Same error at kannel1.log file, when received the SMS DLRs of kannel2's
>> messages
>>
>> Please help me to resolve the issue, to route the DLRs into its
>> respective kannel's i.e., Kannel1's sent sms dlr into kannel1 & kannel2's
>> sent sms dlr into kannel2.
>>
>> Thanks,
>> Mahesh
>>
>>