Re: Fwd: Coolpix 4300 Not Found on CHIP Linux

Allen Ginzburg <[email protected]>
Newsgroups gmane.comp.multimedia.gphoto.user
Message-ID <CAE5GHkdJyHtmsPagPNtxMUQet9fsqFd04zTHwv=+rqTY+CfG-Q@mail.gmail.com>
There are no "usbscsi:" ports reported.  Only 4 serial (ttyS0 though ttyS3)
and usb:001,003.  Modprobe sg reports "Module sg not found".

On Fri, Mar 3, 2017 at 9:02 AM, Marcus Meissner <[email protected]> wrote:

> On Thu, Mar 02, 2017 at 12:57:15PM -0800, Allen Ginzburg wrote:
> > On Wed, Mar 1, 2017 at 11:38 PM, Marcus Meissner <[email protected]>
> > wrote:
> >
> > > On Wed, Mar 01, 2017 at 03:15:36PM -0800, Allen Ginzburg wrote:
> > > > I want to control the Coolpix 4300 from this $9 single board
> computer.
> > > The
> > > > camera shows up as:
> > > >
> > > > Bus 001 Device 023: ID 04b0:010e Nikon Corp. Coolpix 4300 (storage)
> > > >
> > > > But is not found by gphoto2 (version 2.5.4).  The listing of
> supported
> > > > cameras shows this camera supported in sierra mode, but the only USB
> > > modes
> > > > that the camera configuration allows is storage and ptp.
> > > >
> > > > I cannot unload the mass-storage driver on this computer.  Is there
> any
> > > way
> > > > to get gphoto2 to control this camera on this system?
> > >
> > > Sierra mode on the Coolpix 4300 is "tunneled" through the Mass Storage
> > > mode.
> > >
> > > So switch the camera to mass storage mode.
> > >
> > > WHat does "gphoto2 --auto-detect" show? WHat does "gphoto2
> --list-ports"
> > > show?
> > >
> > > The USB or SCSI generic device might still need write permissions of
> your
> > > user,
> > > or you can run as root if this is a small computer.
> > >
> > > Ciao, Marcus
> > >
> >
> > I am running as super-user and auto-detect doesn't find anything.  Here
> is
> > the output:
> >
> >  root@chip:~# lsusb | grep Nikon
> > Bus 001 Device 025: ID 04b0:010e Nikon Corp. Coolpix 4300 (storage)
> > root@chip:~# gphoto2 --auto-detect
> > Model                          Port
>
> And
>         gphoto2 --list-ports
> ?
>
> Can you also run:
>         modprobe sg
>
>
> and see if that changes gphoto2 --auto-detect   output?
>
> It should provide "usbscsi:" ports.
>
> Cioao, Marcus
>

------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, SlashDot.org! http://sdm.link/slashdot

_______________________________________________
Gphoto-user mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/gphoto-user
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.