Re: asa 5505 vpn ipsec l2l problem

On Sat, Oct 3, 2009 at 5:38 AM, Hrvoje Popovski <[email protected]> wrote:

>  > If you're not seeing IPsec build the tunnel with debug crypto, I would
>
>> guess that traffic is getting NAT'd out, and not hitting the tunnel (by
>> the way, you probably only need debug crypto ipsec 5, not 100...)
>>
>>
>> Do you have NAT setup on the 5505? If you do, do you have a NAT exclude
>> ACL setup that excludes "your device networks -> remote device networks"?
>>
>> --
>> Eric
>>
>>
> hello eveyone,
>
> first thanks everyone who replay on my post.
> I can't established SA, crypto acl is the same on both ends, well they tell
> me so. I can't see config on other side but maybe from log that i can se on
> my ASA i think that problem is on my side. I realy don't know maybe problem
> is in licence (10 inside hosts) but i have only 2 inside hosts
> (192.168.11.11 and 11.12).
> I will try to apply crypto acl with ip rule and see what happens.
>
>
I think this was previously mentioned by Paul Melson... try to use IP
addresses in your IPsec interesting traffic ACL... I agree with him, that
having specific ports in ACL1 is the problem, as far as I know

So ACL1 is now:
access-list ACL1 extended permit tcp host 192.168.11.11 host 10.1.100.13 eq
4000
access-list ACL1 extended permit tcp host 192.168.11.11 host 10.1.110.250 eq
4000
access-list ACL1 extended permit tcp host 192.168.11.11 eq ftp host
10.1.100.105 eq ftp
access-list ACL1 extended permit tcp host 192.168.11.11 host 10.1.100.105 eq
ftp-data
access-list ACL1 extended permit tcp host 192.168.11.12 host 10.1.100.13 eq
4000
access-list ACL1 extended permit tcp host 192.168.11.12 host 10.1.110.250 eq
4000
access-list ACL1 extended permit tcp host 192.168.11.12 host 10.1.100.105 eq
ftp
access-list ACL1 extended permit tcp host 192.168.11.12 host 10.1.100.105 eq
ftp-data

ACL1 should be:
access-list ACL1 extended permit ip host 192.168.11.11 host 10.1.100.13
access-list ACL1 extended permit ip host 192.168.11.11 host 10.1.110.250
access-list ACL1 extended permit ip host 192.168.11.11 host 10.1.100.105
access-list ACL1 extended permit ip host 192.168.11.11 host 10.1.100.105
access-list ACL1 extended permit ip host 192.168.11.12 host 10.1.100.13
access-list ACL1 extended permit ip host 192.168.11.12 host 10.1.110.250
access-list ACL1 extended permit ip host 192.168.11.12 host 10.1.100.105
access-list ACL1 extended permit ip host 192.168.11.12 host 10.1.100.105

At least try this config, and see if it works... worst case roll it back to
what you had before.

Do a 'debug cry isa 5' and try to ping a remote host from e.g. 10.1.100.13
and see if the tunnel tries to build

--
Eric

_______________________________________________
firewall-wizards mailing list
[email protected]
https://listserv.icsalabs.com/mailman/listinfo/firewall-wizards