RE: Code V5R1M0 doesn't report events back after Win2k upgrade
"Hak Lui" <[email protected]>
| Newsgroups | gmane.comp.systems.as400.code |
|---|---|
| Message-ID | <[email protected]> |
I assume that you have no problem in 'pinging' to/from your
AS400COM/workstation?
I assume that you have checked with your system admin folks that your
iSeries/workstation network configuration not changed?
Do you know what COMMSOFT is? This is shown when you have DNS checked on
your STRCODE Setting; or it will be an IP address.
What are the STRCODE Settings on your Console? The port setting must
match that in STRCODE command.
Best regards,
Hak
_______________________
Hak Lui
AS/400 AD, IBM Canada Ltd.
e-mail: [email protected]
Buck Calabro
<Buck.Calabro@comms To: CODE/400 Discussion & Support <code400-l-Zwy7GipZuJhWk0Htik3J/[email protected]>
oft.net> cc:
Sent by: Subject: RE: Code V5R1M0 doesn't report events back after Win2k upgrade
code400-l-bounces@m
idrange.com
05/20/2003 01:40 PM
Please respond to
CODE/400 Discussion
& Support
>try STRCODE with *RESOLVE on your iSeries again
>to see if it helps;
STRCODE SERVER(AS400COM) RMTLOCNAME(*RESOLVE)
No good. If I don't specify the port, I get the following message:
Message ID . . . . . . : EVF4001
Message . . . . : The port number specified is not correct.
Cause . . . . . : The port value specified was 00.
STRCODE SERVER(AS400COM) RMTLOCNAME(*RESOLVE) PORT(4200)
When I specify port 4200, I get an error window with the following:
Handshake information from the host server contains errors.
Connection request from 'COMMSOFT' has been ended by the daemon.
The unusual thing about this is that the iSeries I am running this from is
called AS400COM.
>DUMPOBJ STRCODE *USRSPC to SPL and check if the
>IP address is correct for your workstation.
I did, and it was. Just for grins, I deleted the user space and let
STRCODE
re-create it. No luck.
>Make sure that you apply TWEAK if you want the
>completion message to be popped up.
Thanks, but there's no message to pop up; nothing to change focus to.
Thanks for trying Hak! I appreciate it!
--buck
_______________________________________________
This is the CODE/400 Discussion & Support (CODE400-L) mailing list
To post a message email: CODE400-L-Zwy7GipZuJhWk0Htik3J/[email protected]
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/code400-l
or email: CODE400-L-request-Zwy7GipZuJhWk0Htik3J/[email protected]
Before posting, please take a moment to review the archives
at http://archive.midrange.com/code400-l.
NOTE: WDSc for iSeries disucssion has it's own mailing list.
Information can be found at
http://lists.midrange.com/cgi-bin/listinfo/wdsc-l
_______________________________________________
This is the CODE/400 Discussion & Support (CODE400-L) mailing list
To post a message email: CODE400-L-Zwy7GipZuJhWk0Htik3J/[email protected]
To subscribe, unsubscribe, or change list options,
visit: http://lists.midrange.com/mailman/listinfo/code400-l
or email: CODE400-L-request-Zwy7GipZuJhWk0Htik3J/[email protected]
Before posting, please take a moment to review the archives
at http://archive.midrange.com/code400-l.
NOTE: WDSc for iSeries disucssion has it's own mailing list.
Information can be found at http://lists.midrange.com/cgi-bin/listinfo/wdsc-l