[Bug 922] ERR [125] COMREC invalid command received/no DIS or DTC

[email protected]
Newsgroups gmane.comp.telephony.fax.hylafax.devel
Message-ID <[email protected]> 
http://bugs.hylafax.org/show_bug.cgi?id=922





------- Comment #4 from [email protected]  2009-12-06 05:13 -------
(In reply to comment #3)
> Okay, so show us the log where it worked.
> 
Hi Lee,

here's the sending log:
Dec 02 18:14:11.22: [ 5482]: SESSION BEGIN 000000001 xxxxxxxx
Dec 02 18:14:11.22: [ 5482]: HylaFAX (tm) Version 4.4.0
Dec 02 18:14:11.22: [ 5482]: SEND FAX: JOB 1 DEST 45 COMMID 000000001 DEVICE
'/dev/ttyS1' FROM 'xxxxxx <xxxxxx@localhost>' USER xxxxxx
Dec 02 18:14:11.22: [ 5482]: <-- [12:AT+FCLASS=1\r]
Dec 02 18:14:11.27: [ 5482]: --> [2:OK]
Dec 02 18:14:11.27: [ 5482]: MODEM set XON/XOFF/FLUSH: input ignored, output
disabled
Dec 02 18:14:11.28: [ 5482]: DIAL 45
Dec 02 18:14:11.28: [ 5482]: <-- [9:ATX3DT45\r]
Dec 02 18:14:36.40: [ 5482]: --> [7:CONNECT]
Dec 02 18:14:37.07: [ 5482]: --> [2:OK]
Dec 02 18:14:37.07: [ 5482]: REMOTE CSI "+xxxxxxxxxxxx"
Dec 02 18:14:37.07: [ 5482]: <-- [9:AT+FRH=3\r]
Dec 02 18:14:37.12: [ 5482]: --> [7:CONNECT]
Dec 02 18:14:37.34: [ 5482]: --> [2:OK]
Dec 02 18:14:37.34: [ 5482]: REMOTE best rate 14400 bit/s
Dec 02 18:14:37.34: [ 5482]: REMOTE max A4 page width (215 mm)
Dec 02 18:14:37.34: [ 5482]: REMOTE max unlimited page length
Dec 02 18:14:37.34: [ 5482]: REMOTE best vres 7.7 line/mm
Dec 02 18:14:37.34: [ 5482]: REMOTE format support: MH
Dec 02 18:14:37.34: [ 5482]: REMOTE best 0 ms/scanline
Dec 02 18:14:37.34: [ 5482]: USE 14400 bit/s
Dec 02 18:14:37.34: [ 5482]: SEND file "docq/doc1.ps;c1"
Dec 02 18:14:37.34: [ 5482]: USE A4 page width (215 mm)
Dec 02 18:14:37.34: [ 5482]: USE unlimited page length
Dec 02 18:14:37.34: [ 5482]: USE 7.7 line/mm
Dec 02 18:14:37.34: [ 5482]: USE 1-D MH
Dec 02 18:14:37.34: [ 5482]: USE 0 ms/scanline
Dec 02 18:14:37.34: [ 5482]: SEND training at v.17 14400 bit/s
Dec 02 18:14:37.34: [ 5482]: <-- [9:AT+FRS=7\r]
Dec 02 18:14:37.45: [ 5482]: --> [2:OK]
Dec 02 18:14:37.45: [ 5482]: <-- [9:AT+FTH=3\r]
Dec 02 18:14:37.57: [ 5482]: --> [7:CONNECT]
Dec 02 18:14:37.57: [ 5482]: <-- data [23]
Dec 02 18:14:37.57: [ 5482]: <-- data [2]
Dec 02 18:14:39.31: [ 5482]: --> [7:CONNECT]
Dec 02 18:14:39.31: [ 5482]: <-- data [6]
Dec 02 18:14:39.31: [ 5482]: <-- data [2]
Dec 02 18:14:40.01: [ 5482]: --> [2:OK]
Dec 02 18:14:40.01: [ 5482]: <-- [9:AT+FTS=7\r]
Dec 02 18:14:40.13: [ 5482]: --> [2:OK]
Dec 02 18:14:40.13: [ 5482]: MODEM set XON/XOFF/FLUSH: input interpreted,
output disabled
Dec 02 18:14:40.13: [ 5482]: <-- [11:AT+FTM=145\r]
Dec 02 18:14:41.57: [ 5482]: --> [7:CONNECT]
Dec 02 18:14:41.57: [ 5482]: <-- data [1024]
Dec 02 18:14:41.57: [ 5482]: <-- data [1024]
Dec 02 18:14:41.57: [ 5482]: <-- data [652]
Dec 02 18:14:41.57: [ 5482]: <-- data [2]
Dec 02 18:14:43.13: [ 5482]: --> [2:OK]
Dec 02 18:14:43.13: [ 5482]: MODEM set XON/XOFF/DRAIN: input ignored, output
disabled
Dec 02 18:14:43.13: [ 5482]: <-- [9:AT+FRH=3\r]
Dec 02 18:14:44.37: [ 5482]: --> [7:CONNECT]
Dec 02 18:14:44.51: [ 5482]: --> [2:OK]
Dec 02 18:14:44.51: [ 5482]: TRAINING succeeded
Dec 02 18:14:44.51: [ 5482]: <-- [9:AT+FRS=7\r]
Dec 02 18:14:44.62: [ 5482]: --> [2:OK]
Dec 02 18:14:44.62: [ 5482]: <-- [11:AT+FTM=146\r]
Dec 02 18:14:44.81: [ 5482]: --> [7:CONNECT]
Dec 02 18:14:44.81: [ 5482]: MODEM set XON/XOFF/FLUSH: input interpreted,
output disabled
Dec 02 18:14:44.81: [ 5482]: SEND begin page
Dec 02 18:14:44.83: [ 5482]: Reading MMR-compressed image file
Dec 02 18:14:44.85: [ 5482]: <-- data [1026]
Dec 02 18:14:44.85: [ 5482]: <-- data [1026]
Dec 02 18:14:44.85: [ 5482]: <-- data [1024]
Dec 02 18:14:44.85: [ 5482]: <-- data [1024]
Dec 02 18:14:44.85: [ 5482]: <-- data [1026]
Dec 02 18:14:46.84: [ 5482]: <-- data [1025]
Dec 02 18:14:46.84: [ 5482]: <-- data [1024]
Dec 02 18:14:46.84: [ 5482]: <-- data [1024]
Dec 02 18:14:48.84: [ 5482]: <-- data [1024]
Dec 02 18:14:48.84: [ 5482]: <-- data [1024]
Dec 02 18:14:48.84: [ 5482]: <-- data [1024]
Dec 02 18:14:48.84: [ 5482]: <-- data [1025]
Dec 02 18:14:50.84: [ 5482]: <-- data [1027]
Dec 02 18:14:50.84: [ 5482]: <-- data [1028]
Dec 02 18:14:50.84: [ 5482]: <-- data [1027]
Dec 02 18:14:50.84: [ 5482]: <-- data [1026]
Dec 02 18:14:52.83: [ 5482]: <-- data [1028]
Dec 02 18:14:52.83: [ 5482]: <-- data [1027]
Dec 02 18:14:52.83: [ 5482]: <-- data [1025]
Dec 02 18:14:54.83: [ 5482]: <-- data [1027]
Dec 02 18:14:54.83: [ 5482]: <-- data [1026]
Dec 02 18:14:54.83: [ 5482]: <-- data [1029]
Dec 02 18:14:54.83: [ 5482]: <-- data [1026]
Dec 02 18:14:56.83: [ 5482]: <-- data [1025]
Dec 02 18:14:56.83: [ 5482]: <-- data [1025]
Dec 02 18:14:56.83: [ 5482]: <-- data [1026]
Dec 02 18:14:56.83: [ 5482]: <-- data [1026]
Dec 02 18:14:58.82: [ 5482]: <-- data [1027]
Dec 02 18:14:58.82: [ 5482]: <-- data [1025]
Dec 02 18:15:00.82: [ 5482]: <-- data [1026]
Dec 02 18:15:00.82: [ 5482]: <-- data [1025]
Dec 02 18:15:00.82: [ 5482]: <-- data [1026]
Dec 02 18:15:00.82: [ 5482]: <-- data [1027]
Dec 02 18:15:02.82: [ 5482]: <-- data [1026]
Dec 02 18:15:02.82: [ 5482]: <-- data [1025]
Dec 02 18:15:02.82: [ 5482]: <-- data [1025]
Dec 02 18:15:02.82: [ 5482]: <-- data [1026]
Dec 02 18:15:04.81: [ 5482]: <-- data [1027]
Dec 02 18:15:04.81: [ 5482]: <-- data [1027]
Dec 02 18:15:04.81: [ 5482]: <-- data [1025]
Dec 02 18:15:04.81: [ 5482]: <-- data [1026]
Dec 02 18:15:06.81: [ 5482]: <-- data [1029]
Dec 02 18:15:06.81: [ 5482]: <-- data [1026]
Dec 02 18:15:06.81: [ 5482]: <-- data [1026]
Dec 02 18:15:08.80: [ 5482]: <-- data [1026]
Dec 02 18:15:08.80: [ 5482]: <-- data [1026]
Dec 02 18:15:08.80: [ 5482]: <-- data [1026]
Dec 02 18:15:08.80: [ 5482]: <-- data [1026]
Dec 02 18:15:10.04: [ 5482]: <-- data [1028]
Dec 02 18:15:12.04: [ 5482]: <-- data [1024]
Dec 02 18:15:12.04: [ 5482]: <-- data [1024]
Dec 02 18:15:12.04: [ 5482]: <-- data [1024]
Dec 02 18:15:12.04: [ 5482]: <-- data [1024]
Dec 02 18:15:14.04: [ 5482]: <-- data [1024]
Dec 02 18:15:14.04: [ 5482]: <-- data [1024]
Dec 02 18:15:14.04: [ 5482]: <-- data [1026]
Dec 02 18:15:14.04: [ 5482]: <-- data [1027]
Dec 02 18:15:16.03: [ 5482]: <-- data [1026]
Dec 02 18:15:16.03: [ 5482]: <-- data [1026]
Dec 02 18:15:16.03: [ 5482]: <-- data [1025]
Dec 02 18:15:18.03: [ 5482]: <-- data [1024]
Dec 02 18:15:18.03: [ 5482]: <-- data [805]
Dec 02 18:15:18.03: [ 5482]: SENT 63269 bytes of data
Dec 02 18:15:18.03: [ 5482]: SEND 1D RTC
Dec 02 18:15:18.03: [ 5482]: <-- data [29]
Dec 02 18:15:18.03: [ 5482]: <-- data [2]
Dec 02 18:15:18.03: [ 5482]: SEND end page
Dec 02 18:15:20.07: [ 5482]: --> [2:OK]
Dec 02 18:15:20.07: [ 5482]: MODEM set XON/XOFF/DRAIN: input ignored, output
disabled
Dec 02 18:15:20.07: [ 5482]: <-- [9:AT+FTS=9\r]
Dec 02 18:15:20.20: [ 5482]: --> [2:OK]
Dec 02 18:15:20.20: [ 5482]: SEND send EOP (no more pages or documents)
Dec 02 18:15:20.20: [ 5482]: <-- [9:AT+FTH=3\r]
Dec 02 18:15:20.32: [ 5482]: --> [7:CONNECT]
Dec 02 18:15:20.32: [ 5482]: <-- data [3]
Dec 02 18:15:20.32: [ 5482]: <-- data [2]
Dec 02 18:15:21.53: [ 5482]: --> [2:OK]
Dec 02 18:15:21.53: [ 5482]: <-- [9:AT+FRH=3\r]
Dec 02 18:15:22.80: [ 5482]: --> [7:CONNECT]
Dec 02 18:15:22.93: [ 5482]: --> [2:OK]
Dec 02 18:15:22.93: [ 5482]: SEND recv MCF (message confirmation)
Dec 02 18:15:22.94: [ 5482]: SEND FAX (000000001): FROM xxxxxx@localhost TO 45
(page 1 of 1 sent in 0:45)
Dec 02 18:15:22.94: [ 5482]: <-- [9:AT+FRS=7\r]
Dec 02 18:15:23.04: [ 5482]: --> [2:OK]
Dec 02 18:15:23.04: [ 5482]: SEND FAX (000000001): FROM xxxxxx@localhost TO 45
(docq/doc1.ps;c1 sent in 0:46)
Dec 02 18:15:23.94: [ 5482]: <-- [9:AT+FTH=3\r]
Dec 02 18:15:24.06: [ 5482]: --> [7:CONNECT]
Dec 02 18:15:24.06: [ 5482]: <-- data [3]
Dec 02 18:15:24.06: [ 5482]: <-- data [2]
Dec 02 18:15:25.27: [ 5482]: --> [2:OK]
Dec 02 18:15:25.27: [ 5482]: MODEM input buffering enabled
Dec 02 18:15:26.27: [ 5482]: <-- [5:ATH0\r]
Dec 02 18:15:26.73: [ 5482]: --> [2:OK]
Dec 02 18:15:26.73: [ 5482]: MODEM set DTR OFF
Dec 02 18:15:26.74: [ 5482]: SESSION END
---
TIA
Roman


-- 
Configure bugmail: http://bugs.hylafax.org/userprefs.cgi?tab=email
------- You are receiving this mail because: -------
You are the assignee for the bug, or are watching the assignee.


____________________ HylaFAX(tm) Developers Mailing List ____________________
  To subscribe/unsubscribe, click http://lists.hylafax.org/cgi-bin/lsg2.cgi
On UNIX: mail -s unsubscribe [email protected] < /dev/null
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.