Re: Problem with Zoom USB modem

I left off the top bit of legalese


#
# Configuration for a Rockwell RC288DPi-based Class 1 modem.
#    Hayes Optima 28800 firmware rev ???
#    Microcom DeskPorte 28.8S firmware rev V1.100K-V34_DS
#    PPI PM288FXMT firmware rev 1.57
#
# Note that the modem does not lock the line rate for fax
# receive (at least not the PM288FXMT); but not sure whether
# current flow control settings are maintained or if it
# switches to XON/XOFF (testing host was too fast to see).
#
#
CountryCode: 1
AreaCode: 502
FAXNumber: +1.502.896.2382
LongDistancePrefix: 1
InternationalPrefix: 011
DialStringRules: etc/dialrules
ServerTracing: 0xFFF
SessionTracing: 11
RecvFileMode: 0666
LogFileMode: 0600
DeviceMode: 0600
RingsBeforeAnswer: 1
SpeakerVolume: off
GettyArgs: "-h %l dx_%s"
LocalIdentifier: CTI-KY
TagLineFont: etc/lutRS18.pcf
TagLineFormat: "From %%l|%c|Page %%P of %%T"
MaxConsecutiveBadLines: 3
MaxRecvPages: 50
#
#
# Modem-related stuff: should reflect modem command interface
# and hardware connection/cabling (e.g. flow control).
#
ModemType: Class1 # use this to supply a hint
ModemRate: 19200 # rate for DCE-DTE communication
ModemFlowControl: rtscts # default
#
ModemNoFlowCmd: AT&K0 # setup no flow control
ModemHardFlowCmd: AT&K3 # setup hardware flow control
ModemSoftFlowCmd: AT&K4 # setup software flow control
ModemSetupDTRCmd: AT&D2 # setup so DTR drop resets modem
ModemSetupDCDCmd: AT&C1 # setup so DCD reflects carrier (or not)
#
ModemMfrQueryCmd: !Rockwell
ModemModelQueryCmd: !RC288DPi
ModemRevQueryCmd: ATI3 # product information
#
ModemDialCmd: ATDT%s # T for tone dialing

On Fri, Oct 23, 2015 at 9:22 AM, Christophe BARRY <[email protected]>
wrote:

> Could you please send us the modem config File ?
>
>
> Christophe
>
>
> De : David Denney <[email protected]>
> Date : vendredi 23 octobre 2015 16:13
> À : "[email protected]" <[email protected]>
> Objet : [hylafax-users] Problem with Zoom USB modem
>
> I am trying to set up Hylafax on a Ubuntu 14.04LTS machine.
> I get it all set up and I start getting wedged e-mails.
> I set the server tracing to 0xFFF and when I look at the logs, I get the
> following:
>
> FaxGetty[1450]: DELAY 10 ms
> FaxGetty[1450]: MODEM flush i/o
> FaxGetty[1450]: <-- [4:ATZ\r]
> FaxGetty[1450]: --> [5:ERROR]
> FaxGetty[1450]: MODEM Command error
> FaxGetty[1450]: MODEM set DTR OFF
> FaxGetty[1450]: Unable to setup modem on /dev/ttyACM0; giving up after 2
> attempts
> FaxQueuer[1396]: MODEM /dev/ttyACM0 appears to be wedged
> FaxQueuer[1396]: MODEM WEDGED: bin/wedged "ttyACM0" "/dev/ttyACM0"
> FaxGetty[1450]: CLOSE /dev/ttyACM0
>
> Why would it error out on a reset command? I tried cu to test the modem,
> AT command gives OK, but ATZ, ATZ0, and ATZ1 all error out.
>
> This is a model 3095 USB modem from Zoom (based on Conextant chipset *I
> believe*)
>
> Any ideas?
>
> Thank you in advance
> David
>



-- 
*David Denney*
*IT & Vending Account Manager*

Cutting Tools Inc*. | *www.cuttingtoolsinc.net
1002 Pleasant Grove Pl., Mount Juliet, TN 37122
Office: 615.391.0200 | Fax: 615.391.0206 | Cell: 615.655.7008