Re: Anyone using dvgrab successfully in opensuse 11.0/11.1?

On Fri, May 15, 2009 at 10:44 PM, Woojin Lee <[email protected]> wrote:
> Hi.
> I've tried several computers with opensuse 11.0/11.1 with three different
> firewire cards, two different cables and two different camcoders, and they
> all fail to detect the DV camcoder.  They all used to work under mandriva a
> while ago, but can't seem to get any of them working in opensuse 11.1.  They
> all give more or less the same error.  Here is the typical output.
> BTW, what does "ieee1394: Failed to generate Configuration ROM image for host
> 0" mean?  I keep getting this in dmesg when I run testlibraw.  Can someone
> help please?  Thank you in advance.
>
> Woojin
>
> lspci -vv:
> 02:0f.2 FireWire (IEEE 1394): Texas Instruments PCI4451 IEEE-1394 Controller
> (prog-if 10 [OHCI])
>        Subsystem: Dell PCI4451 IEEE-1394 Controller (Dell Inspiron 8100)
>        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr-
> Stepping- SERR+ FastB2B- DisINTx-
>        Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort-
> <TAbort- <MAbort- >SERR- <PERR- INTx-
>        Latency: 32 (500ns min, 1000ns max), Cache Line Size: 32 bytes
>        Interrupt: pin A routed to IRQ 10
>        Region 0: Memory at f6ffd800 (32-bit, non-prefetchable) [size=2K]
>        Region 1: Memory at f6ff8000 (32-bit, non-prefetchable) [size=16K]
>        Capabilities: [44] Power Management version 2
>                Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
> PME(D0-,D1-,D2+,D3hot+,D3cold-)
>                Status: D0 PME-Enable- DSel=0 DScale=0 PME-
>        Kernel driver in use: ohci1394
>        Kernel modules: ohci1394
>
>
>
> dvgrav:
> Error: no camera exists
>
>
>
> testlibraw:
> successfully got handle
> current generation number: 1
> 1 card(s) found
>  nodes on bus:  1, card name: ohci1394
> using first card found: 1 nodes on bus, local ID is 0, IRM is 0
>
> doing transactions with custom tag handler
> trying to send read request to node 0... completed with value 0xe8a689ba
>
> using standard tag handler and synchronous calls
> trying to read from node 0... completed with value 0xce638aba
>
> testing FCP monitoring on local node
> got fcp command from node 0 of 8 bytes: 01 23 45 67 89 ab cd ef
> got fcp response from node 0 of 8 bytes: 01 23 45 67 89 ab cd ef
> testing config rom stuff
> get_config_rom returned 0, romsize 64, rom_version 4
> here are the first 10 quadlets:
> 0. quadlet: 0xdb5d0404
> 1. quadlet: 0x34393331
> 2. quadlet: 0x32a264e0
> 3. quadlet: 0x00c04f43
> 4. quadlet: 0x21888c24
> 5. quadlet: 0x14db0300
> 6. quadlet: 0xc04f4303
> 7. quadlet: 0x02000081
> 8. quadlet: 0xc083000c
> 9. quadlet: 0x2a2c0600
> update_config_rom returned 0
>
> polling for leftover messages
>
>
> dmesg:
> ieee1394: hpsb_update_config_rom() is deprecated
> ieee1394: Failed to generate Configuration ROM image for host 0
>
>
> lsmod|grep 1394:
> dv1394                 15652  0
> raw1394                21212  0
> ohci1394               27656  1 dv1394
> ieee1394               83764  3 dv1394,raw1394,ohci1394
>

What group is /dev/raw1394 in?

it is likely that you need to change it to a group your user is in.

-- 
Carl K

------------------------------------------------------------------------------
Crystal Reports - New Free Runtime and 30 Day Trial
Check out the new simplified licensing option that enables 
unlimited royalty-free distribution of the report engine 
for externally facing server and web deployment. 
http://p.sf.net/sfu/businessobjects