Re: Terragear 0.9.5 will not compile

Okay, now that I can copypaste, here are the error lines.

if g++ -DHAVE_CONFIG_H -I. -I. -I../../../src/Include 
-I/usr/include/glib-1.2 -I/usr/lib/glib/include -I/usr/local/include 
-I/usr/include/glib-1.2 -I/usr/lib/glib/include -I/usr/X11R6/include -g 
-O2 -MT Heap.o -MD -MP -MF ".deps/Heap.Tpo" -c -o Heap.o Heap.cc; \
then mv -f ".deps/Heap.Tpo" ".deps/Heap.Po"; else rm -f 
".deps/Heap.Tpo"; exit 1; fi
Array.h: In method `void array<T>::resize (int) [with T = heap_node]':
Heap.cc:54:   instantiated from here
Array.h:69: `memcpy' undeclared (first use this function)
Array.h:69: (Each undeclared identifier is reported only once for each 
function it appears in.)
make[3]: *** [Heap.o] Error 1
make[3]: Leaving directory `/flightgear/TerraGear-0.9.5/src/Prep/Terra'
make[2]: *** [all-recursive] Error 1
make[2]: Leaving directory `/flightgear/TerraGear-0.9.5/src/Prep'
make[1]: *** [all-recursive] Error 1
make[1]: Leaving directory `/flightgear/TerraGear-0.9.5/src'
make: *** [all-recursive] Error 1


BR,
Jussi


> 
> Hello All,
> 
> I am a total newbie to Linux and Flightgear / Terragear and have run 
> into several problems, but have managed to sort them out till now.
> 
> I have the following setup:
> 
> Linux Redhat 7.3
> Compaq Pentium 866MHz
> GeForce 2 MX400
> 
> Initially I installed and got these running
> FlightGear 0.9.3
> SimGear 0.3.4
> plib 1.6.0
> 
> Now I would like to compile the Finnish scenery, thus installed
> TerraGear 0.9.5 which needed
> SimGear 0.3.6 (Simgear 0.3.4 make clean) which needed
> openal (CVS)
> gpc231
> gts 0.7.2
> nurbs++3.0.11
> 
> In TerraGear the ./configure goes OK, but in make I get error with 
> heap.o / Heap.cc. I believe this is from glib 1.2
> 
> Array.h:69:`memcpy' undeclared ... etc. (Grr! Do not know how to 
> copypaste the lines from console...)
> 
> I suspected this to be due to old glib, thus I loaded and installed 
> glib2.4.6, which needed
> pkgconfig 0.15.0
> 
> I configured with ./configure --prefix=/opt/glib
> then make and make install
> then as mentined in the gtk manuals
> LD_LIBRARY_PATH="/opt/glib/lib"
> PATH="/opt/glib/bin:$PATH"
> export LD_LIBRARY_PATH PATH
> 
> But this was no help.
> 
> As I said, I am newbie to Linux, so I just try to go with some readme 
> helps etc...
> 
> BR,
> Jussi Korolainen

> _______________________________________________
> Terragear-devel mailing list
> [email protected]
> http://mail.flightgear.org/mailman/listinfo/terragear-devel
> 2f585eeea02e2c79d7b1d8c4963bae2d

__
Älä maksa tekstiviesteistä! Saunalahden Tekstari-GSM-liittymällä lähetät tekstiviestit maksutta kaikkiin liittymiin (1000 kpl/kk).
http://saunalahti.fi


_______________________________________________
Terragear-devel mailing list
[email protected]
http://mail.flightgear.org/mailman/listinfo/terragear-devel
2f585eeea02e2c79d7b1d8c4963bae2d