RE: ASP Capabilities value 0x2 of interworking field

Hi Brian,
This is an important statement that defines IPSPs.

And, if all of the SIGTRAN community feels the same, I feel that this SHOULD
be explicitly stated while defining IPSPs. This definition is completely
missing from the specs and has led to a lot of confusion about the
definition of IPSPs.


The current definition states as follows, which is extremely confusing.
The IPSP definition, from the specs, means that IPSP is similar to ASP only
(not SGP).
And that it does NOT use SGPs while communicating with other IPSPs.

The RFC 3332 has a seperate definition of IPSP, SGP and ASP as follows:

   IP Server Process (IPSP) - A process instance of an IP-based
   application.  An IPSP is essentially the same as an ASP, except that
   it uses M3UA in a point-to-point fashion.  Conceptually, an IPSP does
   not use the services of a Signalling Gateway node.

   Signalling Gateway Process (SGP) - A process instance of a Signalling
   Gateway.  It serves as an active, backup, load-sharing or broadcast
   process of a Signalling Gateway.


We should explicitly write that IPSP can be an ASP or an SGP.


shashank


-----Original Message-----
From: [email protected] [mailto:[email protected]]On
Behalf Of Brian F. G. Bidulock
Sent: Monday, December 19, 2005 6:07 PM
To: Ilie Glib
Cc: [email protected]
Subject: Re: [Sigtran] ASP Capabilities value 0x2 of interworking field


Ilie,

The signalling gateway capability, SS7 interworking and relay capabilities
can be combined into any process (ASP, ISPS, SGP).

--brian

Ilie Glib wrote:                                                      (Mon,
19 Dec 2005 13:17:19)
> Brian,
> 
> I am sorry I was not clear enough. My claim was
> 
> Registration Request (REG REQ) cannot be sent from an SGP, therefore
> the value 0x2 indicating signalling gateway capability is meaningless,
> unless IPSP and SGP functions can be combined in one Signalling
> Process.
> 
> Can an SGP act as an IPSP?
> 
> 
> Thank you
> 
> Ilie
> 
> 
> On 12/19/05, Brian F. G. Bidulock <[email protected]> wrote:
> > Ilie,
> >
> > Ilie Glib wrote:
(Mon, 19 Dec 2005 12:39:07)
> > > Brian,
> > >
> > > could you please answer the following questions
> > >
> > > 1) Can SG register via RKM? If not, why the value 0x2 that indicates
> > > Signalling Gateway?
> >
> > You are confused.  0x2 indicates signalling gateway capability: i.e.,
> > the registering node has an SS7 network interfaces and behaves as an
> > SG when interworking to that interface.
> >
> > >
> > > 2) Is there any difference between capabilities 0x0 and 0x1 in SUA
> > >
> > >      0x0 indicates no interworking with SS7 Networks.
> > >      0x1 indicates IP Signalling Endpoint (ASP), interworking with SS7
> > >         networks.
> >
> > Yes, one supports interworking with SS7 networks and the other does not.
> >
> > >
> > > I was more after a definition of the Relay capability in SUA
> > > framework. Although SUA RFC mentions Relay and describes it, the
> > > definition of Relay is missing.
> >
> > See SCCP specifications for a definition of a relay node.
> >
> > --brian
> >
> > --
> > Brian F. G. Bidulock
> > [email protected]
> > http://www.openss7.org/
> >

-- 
Brian F. G. Bidulock
[email protected]
http://www.openss7.org/

_______________________________________________
Sigtran mailing list
[email protected]
https://www1.ietf.org/mailman/listinfo/sigtran