[ACPI-sppt] Problems with Samsung X10 Notebook (Centrino)

Hello,

problems in short:
- no suspend at all
- no cpu frequency scaling

here is the dmesg log:

>  BIOS-e820: 000000001ff70000 - 000000001ff7c000 (ACPI data)
>  BIOS-e820: 000000001ff7c000 - 000000001ff80000 (ACPI NVS)
> ACPI: have wakeup address 0xc0001000
> ACPI: RSDP (v000 SENSX                      ) @ 0x000f7580
> ACPI: RSDT (v001 SENSX  AQUILA   01540.00000) @ 0x1ff77f34
> ACPI: FADT (v001 SENSX  SENSX10  01540.00000) @ 0x1ff7bf64
> ACPI: BOOT (v001 SENSX  $SBFTBL$ 01540.00000) @ 0x1ff7bfd8
> ACPI: SSDT (v001  INTEL  EISTRef 00000.08192) @ 0x1ff77f64
> ACPI: DSDT (v001 SENSX  AQUILA   01540.00000) @ 0x00000000
> ACPI: BIOS passes blacklist
> ACPI: Subsystem revision 20030522
> ACPI: Interpreter enabled
> ACPI: Using PIC for interrupt routing
> ACPI: System [ACPI] (supports S0 S3 S4 S5)
>     ACPI-1121: *** Error: Method execution failed [\_SB_.ADP1._STA] (Node dff628e0), AE_AML_NO_RETURN_VALUE
>     ACPI-1121: *** Error: Method execution failed [\_SB_.BAT1._STA] (Node dff629e0), AE_AML_NO_RETURN_VALUE
> ACPI: PCI Root Bridge [PCI0] (00:00)
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
> ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
> ACPI: PCI Interrupt Link [LNKA] (IRQs *11)
> ACPI: PCI Interrupt Link [LNKB] (IRQs *11)
> ACPI: PCI Interrupt Link [LNKC] (IRQs *10)
> ACPI: PCI Interrupt Link [LNKD] (IRQs *10)
> ACPI: PCI Interrupt Link [LNKE] (IRQs *5)
> ACPI: PCI Interrupt Link [LNKF] (IRQs 5, disabled)
> ACPI: PCI Interrupt Link [LNKG] (IRQs 10, disabled)
> ACPI: PCI Interrupt Link [LNKH] (IRQs *5)
> ACPI: Embedded Controller [H_EC] (gpe 28)
>     ACPI-0345: *** Error: Handler for [EmbeddedControl] returned AE_BAD_PARAMETER
>     ACPI-1121: *** Error: Method execution failed [\_SB_.PCI0.LPCB.H_EC._REG] (Node c161ff00), AE_BAD_PARAMETER
> ACPI: Power Resource [PFAN] (on)
> ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 5
> ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 10
> PCI: Using ACPI for IRQ routing
> PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
> ACPI: Power Button (FF) [PWRF]
> ACPI: Lid Switch [LID0]
> ACPI: Sleep Button (CM) [SLPB]
> ACPI: Fan [FAN0] (on)
> ACPI: Processor [CPU0] (supports C1 C2, 5 performance states, 8 throttling states)



-------------------------------------------------------
This SF.Net email is sponsored by: INetU
Attention Web Developers & Consultants: Become An INetU Hosting Partner.
Refer Dedicated Servers. We Manage Them. You Get 10% Monthly Commission!
INetU Dedicated Managed Hosting http://www.inetu.net/partner/index.php