[ACPI-sppt] USB insertion hardlocks 2.4.22-pre2/3 (fwd)
Wan Tat Chee <[email protected]>
| Newsgroups | gmane.linux.acpi.support |
|---|---|
| Message-ID | <[email protected]> |
Hi, I've been asked by the USB folks to send this to the ACPI list. There's a problem with the ACPI code in 2.4.22-pre2/3 that causes my Fujitsu P2120 notebook to lock up hard when a USB device such as a mouse or flash drive is inserted. ---------- Forwarded message ---------- Date: Tue, 8 Jul 2003 12:39:45 +0800 (SGT) From: Wan Tat Chee <[email protected]> To: Greg KH <[email protected]> Cc: [email protected] Subject: Re: [Linux-usb-users] USB insertion hardlocks 2.4.22-pre2/3 Hi Greg, (I've installed 2.4.22-pre3 now) Yes, I do have ACPI enabled. That's the reason I went with the 2.4.22-preX series, since ACPI is already incorporated (less patches). I'm not keen on 2.5.x right now.... I found out (after lots of hangs and restarts) that the problem has to do with the IRQ setting of the USB ports. I had the built-in Ethernet port set to Auto in the BIOS (enabled only when on AC power or Ethernet cable plugged in). When powering up in battery-only mode (eth0 disabled), the USB IRQ was set to 10, while it is set to 9 in AC power mode (sharing with eth0/8139too driver). The dmesg logs of both cases are attached. If the IRQ is 10, it will hang the machine hard (regardless of cold-boot, warm-boot or after WinXP). T.C. ---- Wan Tat Chee (Lecturer) School of Computer Science, Univ. Science Malaysia, 11800 Minden, Penang, Malaysia. Rm.625 Ofc Ph: +604 653-3888 x 3617 NRG Lab Admin: +604 659-4757 Rm.601-E Ofc Ph: +604 653-4396 Internet: [email protected] Web: http://nrg.cs.usm.my/~tcwan GPG Key : http://nrg.cs.usm.my/~tcwan/tcw_gpg-20030322.asc F'print : DCF2 B9B2 FA4D 1208 AD59 14CA 9A8F F54D B2C4 63C7
usb-battery-eth.log
(text/plain, 12.8 KB)
Linux version 2.4.22-pre3 (root@tcwlbook) (gcc version 3.2.2 20030222 (Red Hat Linux 3.2.2-5)) #1 Mon Jul 7 18:21:21 MYT 2003 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009c000 (usable) BIOS-e820: 000000000009c000 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000000efe0000 (usable) BIOS-e820: 000000000efe0000 - 000000000efefc00 (ACPI data) BIOS-e820: 000000000efefc00 - 000000000eff0000 (ACPI NVS) BIOS-e820: 000000000eff0000 - 000000000f100000 (reserved) BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) 239MB LOWMEM available. ACPI: have wakeup address 0xc0001000 On node 0 totalpages: 61408 zone(0): 4096 pages. zone(1): 57312 pages. zone(2): 0 pages. ACPI: RSDP (v000 FUJ ) @ 0x000f6f70 ACPI: RSDT (v001 FUJ PAULING3 00261.00000) @ 0x0efec50d ACPI: FADT (v001 FUJ PAULING3 00261.00000) @ 0x0efefa6a ACPI: SSDT (v001 PTLTD ACPIPST1 00000.00001) @ 0x0efefade ACPI: BOOT (v001 FUJ PAULING3 00261.00000) @ 0x0efefbd8 ACPI: DSDT (v001 FUJ PAULING3 00261.00000) @ 0x00000000 ACPI: BIOS passes blacklist ACPI: MADT not present Kernel command line: ro root=LABEL=/ hdc=ide-scsi vga=0x317 video=vesa:ypan resume=/dev/hda8 ide_setup: hdc=ide-scsi No local APIC present or hardware disabled Initializing CPU#0 Detected 925.430 MHz processor. Console: colour dummy device 80x25 Calibrating delay loop... 1841.56 BogoMIPS Memory: 239768k/245632k available (1726k kernel code, 5464k reserved, 616k data, 132k init, 0k highmem) Dentry cache hash table entries: 32768 (order: 6, 262144 bytes) Inode cache hash table entries: 16384 (order: 5, 131072 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes) Page-cache hash table entries: 65536 (order: 6, 262144 bytes) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (32 bytes/line) CPU: L2 Cache: 512K (128 bytes/line) CPU: Processor revision 1.4.1.0, 933 MHz CPU: Code Morphing Software revision 4.3.2-9-566 CPU: 20030108 13:03 official release 28.0.3-4.3.2#1 CPU: After generic, caps: 0080893f 0081813f 0000004e 00000000 CPU: Common caps: 0080893f 0081813f 0000004e 00000000 CPU: Transmeta(tm) Crusoe(tm) Processor TM5800 stepping 03 Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX mtrr: v1.40 (20010327) Richard Gooch ([email protected]) mtrr: detected mtrr type: none ACPI: Subsystem revision 20030619 PCI: PCI BIOS revision 2.10 entry at 0xfd89e, last bus=1 PCI: Using configuration type 1 tbxface-0117 [03] acpi_load_tables : ACPI Tables successfully acquired Parsing all Control Methods:........................................................................................................................................................ Table [DSDT](id F005) - 540 Objects with 46 Devices 152 Methods 24 Regions Parsing all Control Methods: Table [SSDT](id F003) - 3 Objects with 0 Devices 0 Methods 0 Regions ACPI Namespace successfully loaded at root c037dcdc evxfevnt-0093 [04] acpi_enable : Transition to ACPI mode successful evgpeblk-0748 [06] ev_create_gpe_block : GPE 00 to 63 [_GPE] 8 regs at 000000000000FF18 on int 9 Completing Region/Field/Buffer/Package initialization:........................................................................... Initialized 24/24 Regions 0/0 Fields 23/23 Buffers 28/28 Packages (551 nodes) Executing all Device _STA and_INI methods:............................................... 47 Devices found containing: 47 _STA, 7 _INI methods ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: System [ACPI] (supports S0 S3 (swsusp) S4 S5) ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: Embedded Controller [EC] (gpe 0) ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 *9 10 11) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *9 10 11) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *9 10 11) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *9 10 11) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11, disabled) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11, disabled) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11, disabled) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 *9 10 11) ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 7 9 10 *11) ACPI: Power Resource [USBP] (on) PCI: Probing PCI hardware ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10 ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 5 ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11 pci_irq-0297 [23] acpi_pci_irq_derive : Unable to derive IRQ for device 00:0f.0 PCI: No IRQ known for interrupt pin A of device 00:0f.0 PCI: Using ACPI for IRQ routing PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off' isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd Journalled Block Device driver loaded ACPI: AC Adapter [AC] (off-line) ACPI: Battery Slot [CMB1] (battery present) ACPI: Battery Slot [CMB2] (battery absent) ACPI: Power Button (FF) [PWRF] ACPI: Lid Switch [LID] acpi_processor-0899 [28] acpi_processor_get_per: Unsupported address space [127] (control_register) ACPI: Processor [CPU0] (supports C1 C2 C3, 8 throttling states) vesafb: framebuffer at 0xf0000000, mapped to 0xcf80b000, size 3072k vesafb: mode is 1024x768x16, linelength=2048, pages=4 vesafb: protected mode interface info at c000:51d3 vesafb: pmi: set display start = c00c5267, set palette = c00c52b3 vesafb: pmi: ports = 1410 1416 1454 1438 143c 145c 1400 1404 14b0 14b2 14b4 vesafb: scrolling: ypan using protected mode interface, yres_virtual=1536 vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled floppy0: no floppy controllers found RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize Linux agpgart interface v0.99 (c) Jeff Hartmann agpgart: Maximum main memory to use for agp memory: 189M agpgart: no supported devices found. Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ALI15X3: IDE controller at PCI slot 00:0f.0 pci_irq-0297 [22] acpi_pci_irq_derive : Unable to derive IRQ for device 00:0f.0 PCI: No IRQ known for interrupt pin A of device 00:0f.0 ALI15X3: chipset revision 195 ALI15X3: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x1800-0x1807, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x1808-0x180f, BIOS settings: hdc:DMA, hdd:pio hda: TOSHIBA MK3021GAS, ATA DISK drive blk: queue c0395320, I/O limit 4095Mb (mask 0xffffffff) hdc: TOSHIBA DVD-ROM SD-R2212, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: attached ide-disk driver. hda: host protected area => 1 hda: 58605120 sectors (30006 MB), CHS=3648/255/63, UDMA(66) Partition check: hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 > Linux Kernel Card Services 3.1.22 options: [pci] [cardbus] [pm] Intel PCIC probe: not found. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 2048 buckets, 16Kbytes TCP: Hash tables configured (established 16384 bind 32768) Linux IP multicast router 0.06 plus PIM-SM NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. Yenta IRQ list 0cf8, PCI irq9 Socket status: 30000006 Resume Machine: This is normal swap space Swsusp 1.0_pre16-2_4_21: kswsuspd starting RAMDISK: Compressed image found at block 0 Freeing initrd memory: 82k freed VFS: Mounted root (ext2 filesystem). EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. (recovery.c, 256): journal_recover: JBD: recovery, exit status 0, recovered transactions 45510 to 45523 (recovery.c, 258): journal_recover: JBD: Replayed 476 and revoked 0/1 blocks kjournald starting. Commit interval 5 seconds EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. Freeing unused kernel memory: 132k freed usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb-ohci.c: USB OHCI at membase 0xcfb2c000, IRQ 11 usb-ohci.c: usb-00:02.0, ALi Corporation USB 1.1 Controller usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 3 ports detected PCI: Enabling device 00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 00:09.0 to 64 usb-ohci.c: USB OHCI at membase 0xcfb2e000, IRQ 9 usb-ohci.c: usb-00:09.0, NEC Corporation USB usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 1 port detected PCI: Enabling device 00:09.1 (0000 -> 0002) PCI: Setting latency timer of device 00:09.1 to 64 usb-ohci.c: USB OHCI at membase 0xcfb30000, IRQ 9 usb-ohci.c: usb-00:09.1, NEC Corporation USB (#2) usb.c: new USB bus registered, assigned bus number 3 hub.c: USB hub found hub.c: 1 port detected PCI: Enabling device 00:09.2 (0000 -> 0002) ehci_hcd 00:09.2: NEC Corporation USB 2.0 ehci_hcd 00:09.2: irq 9, pci mem cfb38000 usb.c: new USB bus registered, assigned bus number 4 PCI: 00:09.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW. PCI: 00:09.2 PCI cache line size corrected to 32. ehci_hcd 00:09.2: USB 2.0 enabled, EHCI 0.95, driver 2003-Jun-19/2.4 hub.c: USB hub found hub.c: 2 ports detected usb.c: registered new driver hiddev usb.c: registered new driver hid hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[email protected]> hid-core.c: USB HID support drivers mice: PS/2 mouse device common for all mice EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,9), internal journal Adding Swap: 1052216k swap-space (priority -1) kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,7), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,5), internal journal EXT3-fs: mounted filesystem with ordered data mode. ohci1394: $Rev: 952 $ Ben Collins <[email protected]> ohci1394_0: OHCI-1394 1.1 (PCI): IRQ=[9] MMIO=[e8016000-e80167ff] Max Packet=[2048] ieee1394: Host added: Node[00:1023] GUID[00000e1000f0496e] [Linux OHCI-1394] SCSI subsystem driver Revision: 1.00 hdc: attached ide-scsi driver. scsi0 : SCSI host adapter emulation for IDE ATAPI devices Vendor: TOSHIBA Model: DVD-ROM SD-R2212 Rev: 1F17 Type: CD-ROM ANSI SCSI revision: 02 cs: IO port probe 0x0c00-0x0cff: clean. cs: IO port probe 0x0100-0x04ff: excluding 0x408-0x40f 0x480-0x48f 0x4d0-0x4d7 cs: IO port probe 0x0a00-0x0aff: clean. Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0 sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.12 ip_tables: (C) 2000-2002 Netfilter core team IPv6 v0.8 for NET4.0 IPv6 over IPv4 tunneling driver 8139too Fast Ethernet driver 0.9.26 eth0: RealTek RTL8139 Fast Ethernet at 0xcfc73800, 00:e0:00:fa:91:46, IRQ 9 eth0: Identified 8139 chip type 'RTL-8139C' eth0: Setting half-duplex based on auto-negotiated partner ability 0000. i2c-core.o: i2c core module version 2.7.0 (20021208) i2c-ali1535.o version 2.7.0 (20021208) i2c-ali1535.o: ALI1535 SMBus Controller detected and initialized fjkeyinf: Application Panel Driver v0.4 fjkeyinf: Copyright (c) 2001 by Jochen Eisinger <[email protected]> SysRq : Emergency Sync Syncing device 03:09 ... OK Syncing device 03:02 ... OK Syncing device 03:06 ... OK Syncing device 03:01 ... OK Syncing device 03:0a ... OK Syncing device 03:07 ... OK Syncing device 03:05 ... OK Done. hub.c: new USB device 00:09.1-1, assigned address 2 usb.c: USB device 2 (vend/prod 0xd7d/0x100) is not claimed by any active driver. Initializing USB Mass Storage driver... usb.c: registered new driver usb-storage scsi1 : SCSI emulation for USB Mass Storage devices Vendor: Model: USB DISK Rev: 2.08 Type: Direct-Access ANSI SCSI revision: 02 WARNING: USB Mass Storage data integrity not assured USB Mass Storage device found at 2 USB Mass Storage support registered.
usb-batteryonly.log
(text/plain, 12.2 KB)
Linux version 2.4.22-pre3 (root@tcwlbook) (gcc version 3.2.2 20030222 (Red Hat Linux 3.2.2-5)) #1 Mon Jul 7 18:21:21 MYT 2003 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009c000 (usable) BIOS-e820: 000000000009c000 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000000efe0000 (usable) BIOS-e820: 000000000efe0000 - 000000000efefc00 (ACPI data) BIOS-e820: 000000000efefc00 - 000000000eff0000 (ACPI NVS) BIOS-e820: 000000000eff0000 - 000000000f100000 (reserved) BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) 239MB LOWMEM available. ACPI: have wakeup address 0xc0001000 On node 0 totalpages: 61408 zone(0): 4096 pages. zone(1): 57312 pages. zone(2): 0 pages. ACPI: RSDP (v000 FUJ ) @ 0x000f6f70 ACPI: RSDT (v001 FUJ PAULING3 00261.00000) @ 0x0efec50d ACPI: FADT (v001 FUJ PAULING3 00261.00000) @ 0x0efefa6a ACPI: SSDT (v001 PTLTD ACPIPST1 00000.00001) @ 0x0efefade ACPI: BOOT (v001 FUJ PAULING3 00261.00000) @ 0x0efefbd8 ACPI: DSDT (v001 FUJ PAULING3 00261.00000) @ 0x00000000 ACPI: BIOS passes blacklist ACPI: MADT not present Kernel command line: ro root=LABEL=/ hdc=ide-scsi vga=0x317 video=vesa:ypan resume=/dev/hda8 ide_setup: hdc=ide-scsi No local APIC present or hardware disabled Initializing CPU#0 Detected 925.403 MHz processor. Console: colour dummy device 80x25 Calibrating delay loop... 1841.56 BogoMIPS Memory: 239768k/245632k available (1726k kernel code, 5464k reserved, 616k data, 132k init, 0k highmem) Dentry cache hash table entries: 32768 (order: 6, 262144 bytes) Inode cache hash table entries: 16384 (order: 5, 131072 bytes) Mount cache hash table entries: 512 (order: 0, 4096 bytes) Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes) Page-cache hash table entries: 65536 (order: 6, 262144 bytes) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (32 bytes/line) CPU: L2 Cache: 512K (128 bytes/line) CPU: Processor revision 1.4.1.0, 933 MHz CPU: Code Morphing Software revision 4.3.2-9-566 CPU: 20030108 13:03 official release 28.0.3-4.3.2#1 CPU: After generic, caps: 0080893f 0081813f 0000004e 00000000 CPU: Common caps: 0080893f 0081813f 0000004e 00000000 CPU: Transmeta(tm) Crusoe(tm) Processor TM5800 stepping 03 Checking 'hlt' instruction... OK. POSIX conformance testing by UNIFIX mtrr: v1.40 (20010327) Richard Gooch ([email protected]) mtrr: detected mtrr type: none ACPI: Subsystem revision 20030619 PCI: PCI BIOS revision 2.10 entry at 0xfd89e, last bus=1 PCI: Using configuration type 1 tbxface-0117 [03] acpi_load_tables : ACPI Tables successfully acquired Parsing all Control Methods:........................................................................................................................................................ Table [DSDT](id F005) - 540 Objects with 46 Devices 152 Methods 24 Regions Parsing all Control Methods: Table [SSDT](id F003) - 3 Objects with 0 Devices 0 Methods 0 Regions ACPI Namespace successfully loaded at root c037dcdc evxfevnt-0093 [04] acpi_enable : Transition to ACPI mode successful evgpeblk-0748 [06] ev_create_gpe_block : GPE 00 to 63 [_GPE] 8 regs at 000000000000FF18 on int 9 Completing Region/Field/Buffer/Package initialization:........................................................................... Initialized 24/24 Regions 0/0 Fields 23/23 Buffers 28/28 Packages (551 nodes) Executing all Device _STA and_INI methods:............................................... 47 Devices found containing: 47 _STA, 7 _INI methods ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: System [ACPI] (supports S0 S3 (swsusp) S4 S5) ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: Embedded Controller [EC] (gpe 0) ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 *9 10 11) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11, disabled) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *9 10 11) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *9 10 11) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11, disabled) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11, disabled) ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11, disabled) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 *9 10 11) ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 7 9 10 *11) ACPI: Power Resource [USBP] (on) PCI: Probing PCI hardware ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10 ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 5 ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11 ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 10 pci_irq-0297 [23] acpi_pci_irq_derive : Unable to derive IRQ for device 00:0f.0 PCI: No IRQ known for interrupt pin A of device 00:0f.0 PCI: Using ACPI for IRQ routing PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off' isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Linux NET4.0 for Linux 2.4 Based upon Swansea University Computer Society NET3.039 Initializing RT netlink socket Starting kswapd Journalled Block Device driver loaded ACPI: AC Adapter [AC] (off-line) ACPI: Battery Slot [CMB1] (battery present) ACPI: Battery Slot [CMB2] (battery absent) ACPI: Power Button (FF) [PWRF] ACPI: Lid Switch [LID] acpi_processor-0899 [28] acpi_processor_get_per: Unsupported address space [127] (control_register) ACPI: Processor [CPU0] (supports C1 C2 C3, 8 throttling states) vesafb: framebuffer at 0xf0000000, mapped to 0xcf80b000, size 3072k vesafb: mode is 1024x768x16, linelength=2048, pages=4 vesafb: protected mode interface info at c000:51d3 vesafb: pmi: set display start = c00c5267, set palette = c00c52b3 vesafb: pmi: ports = 1410 1416 1454 1438 143c 145c 1400 1404 14b0 14b2 14b4 vesafb: scrolling: ypan using protected mode interface, yres_virtual=1536 vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0 Console: switching to colour frame buffer device 128x48 fb0: VESA VGA frame buffer device pty: 256 Unix98 ptys configured Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP enabled floppy0: no floppy controllers found RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize Linux agpgart interface v0.99 (c) Jeff Hartmann agpgart: Maximum main memory to use for agp memory: 189M agpgart: no supported devices found. Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ALI15X3: IDE controller at PCI slot 00:0f.0 pci_irq-0297 [22] acpi_pci_irq_derive : Unable to derive IRQ for device 00:0f.0 PCI: No IRQ known for interrupt pin A of device 00:0f.0 ALI15X3: chipset revision 195 ALI15X3: not 100% native mode: will probe irqs later ide0: BM-DMA at 0x1800-0x1807, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0x1808-0x180f, BIOS settings: hdc:DMA, hdd:pio hda: TOSHIBA MK3021GAS, ATA DISK drive blk: queue c0395320, I/O limit 4095Mb (mask 0xffffffff) hdc: TOSHIBA DVD-ROM SD-R2212, ATAPI CD/DVD-ROM drive ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 ide1 at 0x170-0x177,0x376 on irq 15 hda: attached ide-disk driver. hda: host protected area => 1 hda: 58605120 sectors (30006 MB), CHS=3648/255/63, UDMA(66) Partition check: hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 > Linux Kernel Card Services 3.1.22 options: [pci] [cardbus] [pm] Intel PCIC probe: not found. NET4: Linux TCP/IP 1.0 for NET4.0 IP Protocols: ICMP, UDP, TCP, IGMP IP: routing cache hash table of 2048 buckets, 16Kbytes TCP: Hash tables configured (established 16384 bind 32768) Linux IP multicast router 0.06 plus PIM-SM NET4: Unix domain sockets 1.0/SMP for Linux NET4.0. Yenta IRQ list 0cf8, PCI irq9 Socket status: 30000006 Resume Machine: This is normal swap space Swsusp 1.0_pre16-2_4_21: kswsuspd starting RAMDISK: Compressed image found at block 0 Freeing initrd memory: 82k freed VFS: Mounted root (ext2 filesystem). EXT3-fs: INFO: recovery required on readonly filesystem. EXT3-fs: write access will be enabled during recovery. (recovery.c, 256): journal_recover: JBD: recovery, exit status 0, recovered transactions 45499 to 45509 (recovery.c, 258): journal_recover: JBD: Replayed 435 and revoked 0/1 blocks kjournald starting. Commit interval 5 seconds EXT3-fs: recovery complete. EXT3-fs: mounted filesystem with ordered data mode. Freeing unused kernel memory: 132k freed usb.c: registered new driver usbdevfs usb.c: registered new driver hub usb-ohci.c: USB OHCI at membase 0xcfb2c000, IRQ 11 usb-ohci.c: usb-00:02.0, ALi Corporation USB 1.1 Controller usb.c: new USB bus registered, assigned bus number 1 hub.c: USB hub found hub.c: 3 ports detected PCI: Enabling device 00:09.0 (0000 -> 0002) PCI: Setting latency timer of device 00:09.0 to 64 usb-ohci.c: USB OHCI at membase 0xcfb2e000, IRQ 9 usb-ohci.c: usb-00:09.0, NEC Corporation USB usb.c: new USB bus registered, assigned bus number 2 hub.c: USB hub found hub.c: 1 port detected PCI: Enabling device 00:09.1 (0000 -> 0002) PCI: Setting latency timer of device 00:09.1 to 64 usb-ohci.c: USB OHCI at membase 0xcfb30000, IRQ 10 usb-ohci.c: usb-00:09.1, NEC Corporation USB (#2) usb.c: new USB bus registered, assigned bus number 3 hub.c: USB hub found hub.c: 1 port detected PCI: Enabling device 00:09.2 (0000 -> 0002) ehci_hcd 00:09.2: NEC Corporation USB 2.0 ehci_hcd 00:09.2: irq 9, pci mem cfb38000 usb.c: new USB bus registered, assigned bus number 4 PCI: 00:09.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW. PCI: 00:09.2 PCI cache line size corrected to 32. ehci_hcd 00:09.2: USB 2.0 enabled, EHCI 0.95, driver 2003-Jun-19/2.4 hub.c: USB hub found hub.c: 2 ports detected usb.c: registered new driver hiddev usb.c: registered new driver hid hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[email protected]> hid-core.c: USB HID support drivers mice: PS/2 mouse device common for all mice EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,9), internal journal Adding Swap: 1052216k swap-space (priority -1) kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,7), internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,5), internal journal EXT3-fs: mounted filesystem with ordered data mode. ohci1394: $Rev: 952 $ Ben Collins <[email protected]> ohci1394_0: OHCI-1394 1.1 (PCI): IRQ=[9] MMIO=[e8016000-e80167ff] Max Packet=[2048] ieee1394: Host added: Node[00:1023] GUID[00000e1000f0496e] [Linux OHCI-1394] SCSI subsystem driver Revision: 1.00 hdc: attached ide-scsi driver. scsi0 : SCSI host adapter emulation for IDE ATAPI devices Vendor: TOSHIBA Model: DVD-ROM SD-R2212 Rev: 1F17 Type: CD-ROM ANSI SCSI revision: 02 cs: IO port probe 0x0c00-0x0cff: clean. cs: IO port probe 0x0100-0x04ff: excluding 0x408-0x40f 0x480-0x48f 0x4d0-0x4d7 cs: IO port probe 0x0a00-0x0aff: clean. Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0 sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray Uniform CD-ROM driver Revision: 3.12 ip_tables: (C) 2000-2002 Netfilter core team IPv6 v0.8 for NET4.0 IPv6 over IPv4 tunneling driver 8139too Fast Ethernet driver 0.9.26 i2c-core.o: i2c core module version 2.7.0 (20021208) i2c-ali1535.o version 2.7.0 (20021208) i2c-ali1535.o: ALI1535 SMBus Controller detected and initialized fjkeyinf: Application Panel Driver v0.4 fjkeyinf: Copyright (c) 2001 by Jochen Eisinger <[email protected]> i2c-ali1535.o: Error: command never completed SysRq : Emergency Sync Syncing device 03:09 ... OK Syncing device 03:02 ... OK Syncing device 03:06 ... OK Syncing device 03:01 ... OK Syncing device 03:0a ... OK Syncing device 03:07 ... OK Syncing device 03:05 ... OK Done.