Re: [ACPI-sppt] ACPI but no PMCIA Wireless

Here are some entries from dmesg when I boot in the ACPI supported
kernel:

ACPI: Subsystem revision 20021212
PCI: PCI BIOS revision 2.10 entry at 0xfd89b, last bus=2
PCI: Using configuration type 1
    ACPI-0263: *** Info: GPE Block0 defined as GPE0 to GPE63
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: System [ACPI] (supports S0 S3 S4 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.AGPB._PRT]
ACPI: PCI Interrupt Link [LNK0] (IRQs 7 10, disabled)
ACPI: PCI Interrupt Link [LNK1] (IRQs 7 *10)
ACPI: PCI Interrupt Link [LNK2] (IRQs 7 10, disabled)
ACPI: PCI Interrupt Link [LNK3] (IRQs 7 10, disabled)
ACPI: PCI Interrupt Link [LNK4] (IRQs 7 10, disabled)
ACPI: PCI Interrupt Link [LNK5] (IRQs 7 *11)
ACPI: PCI Interrupt Link [LNK6] (IRQs 7 10, disabled)
ACPI: PCI Interrupt Link [LNK7] (IRQs *5)
ACPI: PCI Interrupt Link [LNK8] (IRQs 7 *10)
ACPI: Embedded Controller [EC0] (gpe 24)
schedule_task(): keventd has not started
PCI: Probing PCI hardware
ACPI: PCI Interrupt Link [LNK0] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNK2] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNK3] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNK4] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNK6] enabled at IRQ 10
PCI: No IRQ known for interrupt pin A of device 00:10.0<6>PCI: Using
ACPI for IRQ routing
PCI: if you experiencce problems, try using option 'pci=noacpi' or even
'acpi=off'
                                                                                
Linux Kernel Card Services 3.1.22
  options:  [pci] [cardbus] [pm]
ds: no socket drivers loaded!
unloading Kernel Card Services

Thanks, 
Mark

On Sun, 2003-09-21 at 19:46, Carl L. Gilbert wrote:
> On Sun, 2003-09-21 at 17:10, Mark Allbritten wrote:
> > I successfully compiled the acpi and it works great.  However if I boot
> > to my custom kernel my Wireless PCMIA card is not recognized. I have
> > compile this on in a compaq presario 2135US running kernal 2.4.20-20.9. 
> > The PMCIA card is a netgear card however it is recognized as a "Lucent
> > Orinoco and Prism Wireless"
> > 
> > Thank You,
> > Mark
> > 
> > 
> 
> You probably neglected to include all the necessary requirements for
> pcmcia wireless cards in your custom build.  what does the log say?
> 
> CL
> 



-------------------------------------------------------
This sf.net email is sponsored by:ThinkGeek
Welcome to geek heaven.
http://thinkgeek.com/sf