2.6.10 regression issues....

rmal zone: 61420 pages, LIFO batch:14
  HighMem zone: 0 pages, LIFO batch:1
DMI 2.3 present.
ACPI: RSDP (v000 ASUS                                  ) @ 0x000f6e20
ACPI: RSDT (v001 ASUS   A7V266-E 0x30303031 MSFT 0x31313031) @ 0x0ffec000
ACPI: FADT (v001 ASUS   A7V266-E 0x30303031 MSFT 0x31313031) @ 0x0ffec080
ACPI: BOOT (v001 ASUS   A7V266-E 0x30303031 MSFT 0x31313031) @ 0x0ffec040
ACPI: DSDT (v001   ASUS A7V266-E 0x00001000 MSFT 0x0100000b) @ 0x00000000
Built 1 zonelists
No local APIC present or hardware disabled
Initializing CPU#0
Kernel command line: ro root=/dev/hdd2 vga=791 video=vesa:pmipal,mtrr splash=0 hdc=ide-scsi
ide_setup: hdc=ide-scsi
CPU 0 irqstacks, hard=c03d8000 soft=c03d7000
PID hash table entries: 1024 (order: 10, 16384 bytes)
Detected 1477.558 MHz processor.
Using tsc for high-res timesource
Console: colour dummy device 80x25
Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
Memory: 255012k/262064k available (1937k kernel code, 6396k reserved, 756k data, 188k init, 0k highmem)
Checking if this processor honours the WP bit even in supervisor mode... Ok.
Calibrating delay loop... 2908.16 BogoMIPS (lpj=1454080)
Security Framework v1.0.0 initialized
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
CPU: After generic identify, caps: 0383f9ff c1c3f9ff 00000000 00000000
CPU: After vendor identify, caps:  0383f9ff c1c3f9ff 00000000 00000000
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 256K (64 bytes/line)
CPU: After all inits, caps:        0383f9ff c1c3f9ff 00000000 00000020
Intel machine check architecture supported.
Intel machine check reporting enabled on CPU#0.
CPU: AMD Duron(TM)Processor stepping 00
Enabling fast FPU save and restore... done.
Enabling unmasked SIMD FPU exception support... done.
Checking 'hlt' instruction... OK.
ACPI: IRQ9 SCI: Edge set to Level Trigger.
checking if image is initramfs...it isn't (no cpio magic); looks like an initrd
Freeing initrd memory: 794k freed
NET: Registered protocol family 16
PCI: PCI BIOS revision 2.10 entry at 0xf0ed0, last bus=1
PCI: Using configuration type 1
mtrr: v2.0 (20020519)
ACPI: Subsystem revision 20041015
    ACPI-0169: *** Error: No object was returned from [\_SB_.PCI0.PX40.UAR2._STA] (Node cff0c8e0), AE_NOT_EXIST
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 9 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 9 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 7 9 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 9 10 11 12 14 15)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCI1._PRT]
Linux Plug and Play Support v0.97 (c) Adam Belay
PnPBIOS: Scanning system for PnP BIOS support...
PnPBIOS: Found PnP BIOS installation structure at 0xc00fbfe0
PnPBIOS: PnP BIOS version 1.0, entry 0xf0000:0xc010, dseg 0xf0000
PnPBIOS: 15 nodes reported by PnP BIOS; 15 recorded by driver
PCI: Using ACPI for IRQ routing
** PCI interrupts are no longer routed automatically.  If this
** causes a device to stop working, it is probably because the
** driver failed to call pci_enable_device().  As a temporary
** workaround, the "pci=routeirq" argument restores the old
** behavior.  If this argument makes the device work again,
** please email the output of "lspci" to [email protected]
** so I can fix the driver.
pnp: 00:0f: ioport range 0xe400-0xe47f could not be reserved
pnp: 00:0f: ioport range 0xe800-0xe83f could not be reserved
Simple Boot Flag at 0x3a set to 0x1
Machine check exception polling timer started.
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 1024 (order 0, 4096 bytes)
Initializing Cryptographic API
vesafb: framebuffer at 0xe0000000, mapped to 0xd0880000, using 3072k, total 131072k
vesafb: mode is 1024x768x16, linelength=2048, pages=84
vesafb: protected mode interface info at c000:551c
vesafb: scrolling: redraw
vesafb: Truecolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
lirc_dev: IR Remote Control driver registered, at major 61 
ACPI: PS/2 Keyboard Controller [PS2K] at I/O 0x60, 0x64, irq 1
ACPI: PS/2 Mouse Controller [PS2M] at irq 12
serio: i8042 AUX port at 0x60,0x64 irq 12
serio: i8042 KBD port at 0x60,0x64 irq 1
io scheduler noop registered
io scheduler anticipatory registered
RAMDISK driver initialized: 16 RAM disks of 8192K size 1024 blocksize
divert: not allocating divert_blk for non-ethernet device lo
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PDC20265: IDE controller at PCI slot 0000:00:06.0
ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 5
PCI: setting IRQ 5 as level-triggered
ACPI: PCI interrupt 0000:00:06.0[A] -> GSI 5 (level, low) -> IRQ 5
PDC20265: chipset revision 2
PDC20265: 100% native mode on irq 5
PDC20265: (U)DMA Burst Bit ENABLED Primary PCI Mode Secondary PCI Mode.
    ide2: BM-DMA at 0xa000-0xa007, BIOS settings: hde:pio, hdf:pio
    ide3: BM-DMA at 0xa008-0xa00f, BIOS settings: hdg:DMA, hdh:pio
Probing IDE interface ide2...
hde: WDC WD800JB-00FMA0, ATA DISK drive
hdf: Maxtor 91536H2, ATA DISK drive
elevator: using anticipatory as default io scheduler
ide2 at 0xb400-0xb407,0xb002 on irq 5
Probing IDE interface ide3...
VP_IDE: IDE controller at PCI slot 0000:00:11.1
ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 11
PCI: setting IRQ 11 as level-triggered
ACPI: PCI interrupt 0000:00:11.1[A] -> GSI 11 (level, low) -> IRQ 11
VP_IDE: chipset revision 6
VP_IDE: not 100% native mode: will probe irqs later
VP_IDE: VIA vt8233 (rev 00) IDE UDMA100 controller on pci0000:00:11.1
    ide0: BM-DMA at 0x8800-0x8807, BIOS settings: hda:DMA, hdb:DMA
    ide1: BM-DMA at 0x8808-0x880f, BIOS settings: hdc:DMA, hdd:DMA
Probing IDE interface ide0...
hda: WDC WD400EB-00CPF0, ATA DISK drive
hdb: WDC WD300BB-00AUA1, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
Probing IDE interface ide1...
hdc: SAMSUNG CDRW/DVD SM-348B, ATAPI CD/DVD-ROM drive
hdd: WDC WD800JB-00FMA0, ATA DISK drive
ide1 at 0x170-0x177,0x376 on irq 15
Probing IDE interface ide3...
Probing IDE interface ide4...
ide4: Wait for ready failed before probe !
Probing IDE interface ide5...
ide5: Wait for ready failed before probe !
hde: max request size: 128KiB
hde: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
hde: cache flushes supported
 hde: hde1
hdf: max request size: 128KiB
hdf: 30015216 sectors (15367 MB) w/2048KiB Cache, CHS=29777/16/63, UDMA(100)
hdf: cache flushes not supported
 hdf: hdf1
hda: max request size: 128KiB
hda: 78165360 sectors (40020 MB) w/2048KiB Cache, CHS=65535/16/63, UDMA(100)
hda: cache flushes not supported
 hda: hda1
hdb: max request size: 128KiB
hdb: 58633344 sectors (30020 MB) w/2048KiB Cache, CHS=58168/16/63, UDMA(100)
hdb: cache flushes not supported
 hdb: hdb1
hdd: max request size: 128KiB
hdd: 156301488 sectors (80026 MB) w/8192KiB Cache, CHS=65535/16/63, UDMA(100)
hdd: cache flushes supported
 hdd: hdd1 hdd2
mice: PS/2 mouse device common for all mice
input: AT Translated Set 2 keyboard on isa0060/serio0
NET: Registered protocol family 2
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
NET: Registered protocol family 1
ACPI: (supports S0 S1 S4 S5)
ACPI wakeup devices: 
PCI0 PCI1 UAR1 USB0 USB1 USB2 
RAMDISK: Compressed image found at block 0
VFS: Mounted root (ext2 filesystem).
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting.  Commit interval 5 seconds
Freeing unused kernel memory: 188k freed
Real Time Clock Driver v1.12
ACPI: Power Button (FF) [PWRF]
ibm_acpi: ec object not found
ACPI: Processor [CPU0] (supports C1)
Unable to handle kernel paging request at virtual address d081bd20
 printing eip:
c02114a6
*pde = 0ff0f067
*pte = 00000000
Oops: 0002 [#1]
PREEMPT 
Modules linked in: video thermal processor fan button battery ac rtc
CPU:    0
EIP:    0060:[<c02114a6>]    Not tainted VLI
EFLAGS: 00010202   (2.6.10-0.rc1.1ark) 
EIP is at acpi_bus_register_driver+0x34/0x54
eax: ce4cf000   ebx: d0830680   ecx: d082ebad   edx: d081bd20
esi: d0830c00   edi: ce4cf000   ebp: c0327fc4   esp: ce4cff94
ds: 007b   es: 007b   ss: 0068
Process insmod (pid: 426, threadinfo=ce4cf000 task=ce45e060)
Stack: c0327fdc d081302a d0830680 c01376d2 c03e8248 00000001 d0830c00 0804b018 
       00000000 00000000 ce4cf000 c0106181 0804b018 00004c80 0804b008 00000000 
       00000000 bffffd58 00000080 0000007b 0000007b 00000080 ffffe410 00000073 
Call Trace:
 [<d081302a>] acpi_video_init+0x2a/0x4b [video]
 [<c01376d2>] sys_init_module+0x172/0x250
 [<c0106181>] sysenter_past_esp+0x52/0x71
Code: ed ff ff ff 8b 5c 24 08 75 3f 85 db b0 ea 74 39 66 b8 00 f0 21 e0 ff 40 14 8b 15 ac 6b 36 c0 c7 03 a8 6b 36 c0 89 1d ac 6b 36 c0 <89> 1a 89 53 04 ff 48 14 8b 40 08 a8 08 74 05 e8 c6 13 0d 00 89 
 <6>note: insmod[426] exited with preempt_count 1
scheduling while atomic: insmod/0x10000001/426
 [<c02e27d5>] schedule+0x4c5/0x570
 [<c014c80b>] unmap_page_range+0x4b/0x80
 [<c02e2cf7>] cond_resched+0x27/0x40
 [<c014ca72>] unmap_vmas+0x232/0x250
 [<c0151883>] exit_mmap+0x83/0x160
 [<c011b8c4>] mmput+0x34/0xc0
 [<c0120234>] do_exit+0x164/0x470
 [<c0117af0>] do_page_fault+0x0/0x644
 [<c010744d>] die+0x18d/0x190
 [<c0117af0>] do_page_fault+0x0/0x644
 [<c011e0d7>] printk+0x17/0x20
 [<c0117f10>] do_page_fault+0x420/0x644
 [<c01d6921>] sub_alloc+0x61/0x170
 [<c01548e7>] vfree+0x27/0x40
 [<c01d6ade>] idr_get_new_above_int+0xae/0x120
 [<c01d6bbf>] idr_get_new+0x1f/0x50
 [<c0117af0>] do_page_fault+0x0/0x644
 [<c0106c6d>] error_code+0x2d/0x38
 [<c02114a6>] acpi_bus_register_driver+0x34/0x54
 [<d081302a>] acpi_video_init+0x2a/0x4b [video]
 [<c01376d2>] sys_init_module+0x172/0x250
 [<c0106181>] sysenter_past_esp+0x52/0x71
usbcore: registered new driver usbfs
usbcore: registered new driver hub
USB Universal Host Controller Interface driver v2.2
ACPI: PCI interrupt 0000:00:11.2[D] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:11.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
uhci_hcd 0000:00:11.2: irq 5, io base 0x8400
uhci_hcd 0000:00:11.2: new USB bus registered, assigned bus number 1
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:11.3[D] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:11.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
uhci_hcd 0000:00:11.3: irq 5, io base 0x8000
uhci_hcd 0000:00:11.3: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
ACPI: PCI interrupt 0000:00:11.4[D] -> GSI 5 (level, low) -> IRQ 5
uhci_hcd 0000:00:11.4: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#3)
uhci_hcd 0000:00:11.4: irq 5, io base 0x7800
usb 1-2: new full speed USB device using uhci_hcd and address 2
uhci_hcd 0000:00:11.4: new USB bus registered, assigned bus number 3
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.0:USB HID core driver
usbcore: registered new driver usbkbd
drivers/usb/input/usbkbd.c: :USB HID Boot Protocol keyboard driver
usbcore: registered new driver usbmouse
drivers/usb/input/usbmouse.c: v1.6:USB HID Boot Protocol mouse driver
EXT3 FS on hdd2, internal journal
Adding 269096k swap on /dev/hdd1.  Priority:-1 extents:1
NTFS driver 2.1.22-WIP [Flags: R/W MODULE].
NTFS volume version 3.1.
NTFS-fs error (device hda1): load_system_files(): Volume is dirty.  Mounting read-only.  Run chkdsk and mount in Windows.
SGI XFS with ACLs, security attributes, realtime, no debug enabled
SGI XFS Quota Management subsystem
XFS mounting filesystem hdf1
Ending clean XFS mount for filesystem: hdf1
SCSI subsystem initialized
ide-scsi is deprecated for cd burning! Use ide-cd and give dev=/dev/hdX as device
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
  Vendor: SAMSUNG   Model: CDRW/DVD SM-348B  Rev: T504
  Type:   CD-ROM                             ANSI SCSI revision: 02
ip_tables: (C) 2000-2002 Netfilter core team
NET: Registered protocol family 17
e100: Intel(R) PRO/100 Network Driver, 3.2.3-k2-NAPI
e100: Copyright(c) 1999-2004 Intel Corporation
ACPI: PCI interrupt 0000:00:0d.0[A] -> GSI 11 (level, low) -> IRQ 11
divert: allocating divert_blk for eth0
e100: eth0: e100_probe: addr 0xde000000, irq 11, MAC addr 00:90:27:75:32:C4
ip_tables: (C) 2000-2002 Netfilter core team
Badness in enable_irq at kernel/irq/manage.c:106
 [<c013c2f0>] enable_irq+0xc0/0x110
 [<d0c524ea>] e100_up+0x16a/0x240 [e100]
 [<d0c51910>] e100_intr+0x0/0x160 [e100]
 [<d0c5388c>] e100_open+0x2c/0x90 [e100]
 [<c02818e6>] dev_open+0x76/0x90
 [<c02858f1>] dev_mc_upload+0x21/0x40
 [<c0282fed>] dev_change_flags+0x5d/0x140
 [<c02c709a>] devinet_ioctl+0x62a/0x6e0
 [<c02c92ca>] inet_ioctl+0xca/0xe0
 [<c02781f5>] sock_ioctl+0x205/0x2c0
 [<c0172181>] sys_ioctl+0x171/0x270
 [<c0117af0>] do_page_fault+0x0/0x644
 [<c0106181>] sysenter_past_esp+0x52/0x71
e100: eth0: e100_watchdog: link up, 100Mbps, half-duplex
NET: Registered protocol family 23
divert: allocating divert_blk for irlan0
ndiswrapper version 0.10+CVS loaded (preempt=yes,smp=no)
ndiswrapper: driver bcmwl5 (Broadcom,07/17/2003, 3.30.15.0) added
apm: BIOS version 1.2 Flags 0x0b (Driver version 1.16ac)
apm: overridden by ACPI.
parport: PnPBIOS parport detected.
parport0: PC-style at 0x378 (0x778), irq 7, dma 3 [PCSPP,TRISTATE,COMPAT,EPP,ECP,DMA]
lp0: using parport0 (interrupt-driven).
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected VIA KT266/KY266x/KT333 chipset
agpgart: Maximum main memory to use for agp memory: 203M
agpgart: AGP aperture is 128M @ 0xf0000000
input: ImExPS/2 Generic Explorer Mouse on isa0060/serio1
ACPI: PCI interrupt 0000:00:0c.0[A] -> GSI 5 (level, low) -> IRQ 5
apm: BIOS version 1.2 Flags 0x0b (Driver version 1.16ac)
apm: disabled on user request.
[drm] Initialized drm 1.0.0 20040925
PCI: Unable to reserve mem region #1:10000000@e0000000 for device 0000:01:00.0
mtrr: 0xe0000000,0x10000000 overlaps existing 0xe0000000,0x8000000
[drm] Initialized radeon 1.12.0 20020828 on minor 0: ATI Technologies Inc Radeon R200 QL [Radeon 8500 LE]
[drm] Used old pci detect: framebuffer loaded
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[drm] Loading R200 Microcode
apm: BIOS version 1.2 Flags 0x0b (Driver version 1.16ac)
apm: disabled on user request.
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[drm] Loading R200 Microcode
apm: BIOS version 1.2 Flags 0x0b (Driver version 1.16ac)
apm: disabled on user request.
agpgart: Found an AGP 2.0 compliant device at 0000:00:00.0.
agpgart: Putting AGP V2 device at 0000:00:00.0 into 1x mode
agpgart: Putting AGP V2 device at 0000:01:00.0 into 1x mode
[drm] Loading R200 Microcode

00:00.0 Host bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333]
00:01.0 PCI bridge: VIA Technologies, Inc. VT8366/A/7 [Apollo KT266/A/333 AGP]
00:05.0 Multimedia audio controller: C-Media Electronics Inc CM8738 (rev 10)
00:06.0 Unknown mass storage controller: Promise Technology, Inc. 20265 (rev 02)
00:0c.0 Multimedia audio controller: Creative Labs SB Live! EMU10k1 (rev 0a)
00:0c.1 Input device controller: Creative Labs SB Live! MIDI/Game Port (rev 0a)
00:0d.0 Ethernet controller: Intel Corp. 82557/8/9 [Ethernet Pro 100] (rev 08)
00:11.0 ISA bridge: VIA Technologies, Inc. VT8233 PCI to ISA Bridge
00:11.1 IDE interface: VIA Technologies, Inc. VT82C586A/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE (rev 06)
00:11.2 USB Controller: VIA Technologies, Inc. USB (rev 1b)
00:11.3 USB Controller: VIA Technologies, Inc. USB (rev 1b)
00:11.4 USB Controller: VIA Technologies, Inc. USB (rev 1b)
01:00.0 VGA compatible controller: ATI Technologies Inc Radeon R200 QL [Radeon 8500 LE]

-----BEGIN PGP SIGNATURE-----
Version: GnuPG v1.2.6 (GNU/Linux)

iD8DBQBBhmmZpYIGqyXDl5wRAm0WAJ9+fPdzqfpEkw68n6gmSMHUDLIqPwCgsUWj
CNIcPou1m+K2YVIWaHR9oD0=
=Inqr
-----END PGP SIGNATURE-----