Re: DRBD failover issue, kernal panic no init found

I already migrated to SSI-1.9.x with the latest DRBD which is based on
drbd-0.7.20 but haven't checked in the update yet.  The latest one in
CVS is based on drbd-0.7.19 and works fine unless you changed your
drbd devices' al-extents parameter.  In that case you would want
drbd-ssi based on drbd-0.7.20.

It seems to me, without much info, your SSIfailover and rc.sysrecover
system scripts weren't setup properly.  You have to modify them for
drbd for root filesystem failover.  The drbd-ssi-1.2.2-20050712
tarball should include a sample of these two system scripts.

Roger


On 7/7/06, Vijay Swami <[email protected]> wrote:
> Roger,
>
> Its drbd-ssi-1.2.2-20050712. It seems like as soon as the master goes
> down, the slave does not resort to using its own copy. I don't see any
> EXT3 FSCK messages like I've seen by searching the list for successful
> fail over messages. The error is most certainly it can't find /sbin/init
> probably because once the connection to the master dies, its not
> properly using its 'own' copy.
>
> I'm wondering if this is related to the Debian /dev/drbd0 vs /dev/drbd/0
> issue that I've read about. I noticed you said you ran into this problem
> on FC2, which is what RHEL3 is based on. Where you using OpenSSI 1.2.x
> or 1.9.x and which version of DRBD?
>
> Thanks.
>
> /vijay
>
> On Thu, 2006-07-06 at 22:50 -0400, Roger Tsang wrote:
> > Are you using drbd-ssi (openSSI modified drbd) and have enabled
> > SSI-failover service?
> >
> > If you like to try the latest drbd-ssi I'll be making a drbd-ssi
> > tarball based on drbd-0.7.20, hopefully sometime this week.
> >
> > Roger
> >
> >
> > On 7/6/06, Vijay Swami <[email protected]> wrote:
> > > Pertinent details:
> > >  * 2 node cluster
> > >  * RHEL3
> > >  * Kernel/OpenSSI ver: 2.4.21-27.0.2.EL_ssi_2 (install from RPM)
> > >  * drbd version 0.7.11 (api:77)
> > >  * SunFire X4100 2 CPU AMD Opteron hardware
> > >
> > > drbd.conf snippet:
> > >
> > >  on host1 {
> > >     device     /dev/drbd/0;
> > >     disk       /dev/sda2;
> > >     nodenum    1;
> > >     address    192.168.1.1:7788;
> > >     meta-disk  /dev/sda3[0];
> > >
> > >
> > >   on host2 {
> > >     device    /dev/drbd/0;
> > >     disk      /dev/sda2;
> > >     nodenum   2;
> > >     address   192.168.1.2:7788;
> > >     meta-disk /dev/sda3[0];
> > >
> > > /etc/fstab:
> > >
> > > /dev/drbd/0 / ext3 defaults,chard,errors=remount-ro,node=1:2 0 1
> > > /dev/sda1 /boot ext3 defaults,node=1:2 1 2
> > > none    /dev/pts        devpts  gid=5,mode=620,node=*   0       0
> > > none    /proc   proc    defaults,node=* 0       0
> > > #none                    /dev/shm                tmpfs   defaults
> > > 0 0
> > >
> > > df output:
> > >
> > > Filesystem           1K-blocks      Used Available Use% Mounted on
> > > /dev/1/drbd/0         10080520   2329744   7238708  25% /
> > > /dev/1/sda1             248895     61612    174433  27% /boot
> > >
> > > The root file system is configured with DRBD, and working great. Each
> > > node can act as an init node when booted up individually. The other node
> > > joins the cluster, and things work great.
> > >
> > > However, I'm having trouble with the failover.
> > >
> > > If I 'unplug' the master node, the slave recognizes the master has gone
> > > down, and attempts to take over. It prints DRBD timeout messages to the
> > > console (as expected), then:
> > >
> > > ipcnameserver ready
> > > Kernel Panic: no init found. Cannot restart
> > >
> > > .. and then it reboots.
> > >
> > > I have a feeling its something fairly simple here, as DRBD itself works
> > > fine when the nodes are booted. I'm assuming its looking for /sbin/init
> > > to start on the slave node but can't find it? I don't know why since
> > > DRBD itself works on either node acting as an init node when they are
> > > booted regardless of sequence.
> > >
> > > Any ideas?
> > >
> > > Thanks.
> > >
> > > /vijay
> > >
> > > Using Tomcat but need to do more? Need to support web services, security?
> > > Get stuff done quickly with pre-integrated technology to make your job easier
> > > Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
> > > http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642
> > > _______________________________________________
> > > Ssic-linux-users mailing list
> > > [email protected]
> > > https://lists.sourceforge.net/lists/listinfo/ssic-linux-users
> > >
> >
>

Using Tomcat but need to do more? Need to support web services, security?
Get stuff done quickly with pre-integrated technology to make your job easier
Download IBM WebSphere Application Server v.1.0.1 based on Apache Geronimo
http://sel.as-us.falkag.net/sel?cmd=lnk&kid=120709&bid=263057&dat=121642