RE: at76c503a on Startup (boot)

	Thanks, I will try not having it on at boot and see what happens.  

-----Original Message-----
From: [email protected]
[mailto:[email protected]] On Behalf Of CE
Sent: Tuesday, December 28, 2004 1:22 PM
To: [email protected]
Subject: Re: [at76c503a-user] at76c503a on Startup (boot)

	A hotplug problem at boot perhaps?  In Debian it says it didn't work
but that message is wrong.


You Wrote:

> Hello all,
> 
>          I have the above assembled and installed on Fedora FC-3, with a
> customised 2.6.9 kernel.
> 
> I have no problems with performance, scanning etc. the driver works as it
> should.
> 
> It will not however on boot, do an insmod, I have to manually disconnect
the
> device and connect again, then I have my setting as they should be...
> 
> The device in question is an SMC2662W USB EZConnect.
> 
> I have made the appropriate modprobe.conf and ifcfg-wlan0 entries, but at
> boot, I still have the "manual" problem, as stated above.
> 
> Any ideas??    
> 
> 
> Regards / Cordialement / Gruss / Saludos 
> 
> Cassidy IT Services
> 
> John Cassidy Dipl.Ingr (Informatique)
> Schleswigstr. 7
> 51065 Cologne / Koeln / Keulen
> 
> EU
> 
> 
> Tel. +49 (0) 177 799 58 56
> 
> Email: [email protected]
> 
> HTTP: www.jdcassidy.net
> 
> 
> -----Original Message-----
> From: [email protected]
> [mailto:[email protected]] On Behalf Of CE
> Sent: 28 December 2004 04:27
> To: [email protected]
> Subject: Re: [at76c503a-user] incompatible pointer type+Fedora Core 3
> 
> 	You should be using the CVS code for 2.6.  Once you get that and
> your kernel sources do (as root) make, make install.  Then replug your
> device and try ifup wlan0
> 
> 
> You Wrote:
> 
> > Dear All,
> > 
> > 	I was hoping that someone from this list could help me with my
> > Linksys WUSB11 version 2.6 working in Fedora Core 3.  Also, I very new
to
> > linux. 
> > 
> > 	The problem I am getting is when I do a make I get the follow
> > message:
> > 
> > At76c503.c
> > In function ieee80211_to_eth
> > Line 3922
> > Warning: Assignment from incompatible pointer type.  
> > 
> > I have also tried the 0.12beta files and get the same error message.
> > Though, I do get the at76c503.o and can do a make install.  After
plugging
> > in the wireless card, I still do not get the blinking lights that would
> > imply that it works.  I then do a dmesg and see that it tries to
download
> > firmware and after that I get a message:
> > 
> > At76c503 unexpected opmode 185
> > 
> > 	I have the KT133 chip set and have not tried a cheap USB hub, short
> > on cash.  I did get it working for a short time by upgrading from Redhat
> 9.0
> > to Fedora Core 3 and it was working most of the time until I patched it.
> > After patching it I also got the above errors.  I then decided that a
> clean
> > install might work better, but was wrong.
> > 
> > 	Any help would be great.
> > 
> > Thanks,
> > Mike            
> > 
> _______________________________________________
> at76c503a-user mailing list
> [email protected]
> http://lists.berlios.de/mailman/listinfo/at76c503a-user
> 
> _______________________________________________
> at76c503a-user mailing list
> [email protected]
> http://lists.berlios.de/mailman/listinfo/at76c503a-user
_______________________________________________
at76c503a-user mailing list
[email protected]
http://lists.berlios.de/mailman/listinfo/at76c503a-user