ECS Desknote A907, Suse 8.2Pro & Linksys WUSB11 2.6

Hello,

I have a problem getting my Linksys WUSB11 working with Suse 8.2 Pro. I have 
read the tutorials mentioned in this list, but nothing worked for me.

After plugging the WUSB11 into my Desknote I get these messages:

Output of dmesg:

frank@dhcppc0:~>dmesg
[...]
hub.c: new USB device 00:14.0-4, assigned address 3
usbdfu.c: get_op_mode() failed: -32
usbdfu.c: downloading firmware
usbdfu.c: remap
uusbdfu.c: resetting device
usbdfu.c: scanning unclaimed devices
usbdfu.c: op_mode = 4
usbdfu.c: firmware already loaded
at76c503.c: downloading external firmware
at76c503.c: firmware version 0.100.4 #16
at76c503.c: using MAC 00:06:25:48:49:5f
at76c503.c: using net device eth1

Output of /var/log/messages

 Oct 12 13:02:42 dhcppc0 /etc/hotplug/net.agent[2000]: Using HW description    
eth-usb-1-2
 Oct 12 13:02:43 dhcppc0 kernel: hub.c: new USB device 00:14.0-4, assigned
 address 3
 Oct 12 13:02:43 dhcppc0 kernel: usbdfu.c: get_op_mode() failed: -32
 Oct 12 13:02:43 dhcppc0 kernel: usbdfu.c: downloading firmware
 Oct 12 13:02:43 dhcppc0 kernel: usbdfu.c: remap
 Oct 12 13:02:45 dhcppc0 kernel: usbdfu.c: resetting device
 Oct 12 13:02:45 dhcppc0 kernel: usbdfu.c: scanning unclaimed devices
 Oct 12 13:02:45 dhcppc0 kernel: usbdfu.c: op_mode = 4
 Oct 12 13:02:45 dhcppc0 kernel: usbdfu.c: firmware already loaded
 Oct 12 13:02:45 dhcppc0 kernel: at76c503.c: downloading external firmware
 Oct 12 13:02:45 dhcppc0 kernel: at76c503.c: firmware version 0.100.4 #16
 Oct 12 13:02:45 dhcppc0 kernel: at76c503.c: using MAC 00:06:25:48:49:5f
 Oct 12 13:02:45 dhcppc0 kernel: at76c503.c: using net device eth1
 Oct 12 13:02:48 dhcppc0 /etc/hotplug/usb.agent[2164]: writing usb-1-3 to
 /var/run/hotplug/net
 Oct 12 13:02:49 dhcppc0 /etc/hotplug/net.agent[2154]: Using HW description
 eth-usb-1-3
 Oct 12 13:02:49 dhcppc0 ifup-wireless: command 'iwconfig eth1 nick dhcppc0'
 returned
 Oct 12 13:02:49 dhcppc0 ifup-wireless: Error for wireless request "Set
 Nickname" (8B1C) :
 Oct 12 13:02:49 dhcppc0 ifup-wireless: SET failed on device eth1 ;
 Operation not supported.
 Oct 12 13:03:01 dhcppc0 kernel: eth1: no IPv6 routers present

The ECS Desknote A907 runs on a Transmeta CPU with an ALI 1535+ Chipset.

For my knowledge I am out of options and I hope that anyone can help me out.

Thanks a lot,

Frank