2.6.32 dvbdev error / Cinvergy XS
Michael G <[email protected]>
| Newsgroups | gmane.linux.drivers.dvb |
|---|---|
| Message-ID | <[email protected]> |
Hi, can someone please help me to get my Cinergy XS (Bus 001 Device 010: ID 0ccd:0043 TerraTec Electronic GmbH) to run in a 2.6.32 RC3 gentoo system? When I use the in-kernel driver I'll get the following output: usb 1-1: new high speed USB device using ehci_hcd and address 10 usb 1-1: configuration #1 chosen from 1 choice em28xx: New device TerraTec Electronic GmbH Cinergy T USB XS @ 480 Mbps (0ccd:0043, interface 0, class 0) em28xx #0: chip ID is em2870 em28xx #0: i2c eeprom 00: 1a eb 67 95 cd 0c 43 00 c0 12 81 00 6a 24 8e 34 em28xx #0: i2c eeprom 10: 00 00 06 57 02 0c 00 00 00 00 00 00 00 00 00 00 em28xx #0: i2c eeprom 20: 44 00 00 00 f0 10 01 00 00 00 00 00 5b 00 00 00 em28xx #0: i2c eeprom 30: 00 00 20 40 20 80 02 20 01 01 00 00 ee 2d 46 4a em28xx #0: i2c eeprom 40: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 em28xx #0: i2c eeprom 50: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 em28xx #0: i2c eeprom 60: 00 00 00 00 00 00 00 00 00 00 24 03 43 00 69 00 em28xx #0: i2c eeprom 70: 6e 00 65 00 72 00 67 00 79 00 20 00 54 00 20 00 em28xx #0: i2c eeprom 80: 55 00 53 00 42 00 20 00 58 00 53 00 00 00 34 03 em28xx #0: i2c eeprom 90: 54 00 65 00 72 00 72 00 61 00 54 00 65 00 63 00 em28xx #0: i2c eeprom a0: 20 00 45 00 6c 00 65 00 63 00 74 00 72 00 6f 00 em28xx #0: i2c eeprom b0: 6e 00 69 00 63 00 20 00 47 00 6d 00 62 00 48 00 em28xx #0: i2c eeprom c0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 em28xx #0: i2c eeprom d0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 em28xx #0: i2c eeprom e0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 em28xx #0: i2c eeprom f0: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 em28xx #0: EEPROM ID= 0x9567eb1a, EEPROM hash = 0x339064dc em28xx #0: EEPROM info: em28xx #0: No audio on board. em28xx #0: 500mA max power em28xx #0: Table at 0x06, strings=0x246a, 0x348e, 0x0000 em28xx #0: Identified as Terratec Cinergy T XS (card=43) em28xx #0: em28xx #0: The support for this board weren't valid yet. em28xx #0: Please send a report of having this working em28xx #0: not to V4L mailing list (and/or to other addresses) Chip ID is not zero. It is not a TEA5767 tuner 0-0060: chip found @ 0xc0 (em28xx #0) xc2028 0-0060: creating new instance xc2028 0-0060: type set to XCeive xc2028/xc3028 tuner usb 1-1: firmware: requesting xc3028-v27.fw xc2028 0-0060: Loading 80 firmware images from xc3028-v27.fw, type: xc2028 firmware, ver 2.7 xc2028 0-0060: Loading firmware for type=BASE (1), id 0000000000000000. xc2028 0-0060: Loading firmware for type=(0), id 000000000000b700. SCODE (20000000), id 000000000000b700: xc2028 0-0060: Loading SCODE for type=MONO SCODE HAS_IF_4320 (60008000), id 0000000000008000. xc2028 0-0060: Incorrect readback of firmware version. xc2028 0-0060: Loading firmware for type=BASE (1), id 0000000000000000. xc2028 0-0060: Loading firmware for type=(0), id 000000000000b700. SCODE (20000000), id 000000000000b700: xc2028 0-0060: Loading SCODE for type=MONO SCODE HAS_IF_4320 (60008000), id 0000000000008000. xc2028 0-0060: Incorrect readback of firmware version. em28xx #0: v4l2 driver version 0.1.2 em28xx #0: V4L2 video device registered as /dev/video1 No /dev/dvb, so no DVT-T. I tried to use the latest v4l-dvb but I can't compile it: /root/v4l-dvb/v4l/dvbdev.c: In function 'init_dvbdev': /root/v4l-dvb/v4l/dvbdev.c:516: error: 'struct class' has no member named 'nodename' make[3]: *** [/root/v4l-dvb/v4l/dvbdev.o] Error 1 make[2]: *** [_module_/root/v4l-dvb/v4l] Error 2 make[2]: Leaving directory `/usr/src/linux-2.6.32-rc3' make[1]: *** [default] Error 2 make[1]: Leaving directory `/root/v4l-dvb/v4l' make: *** [all] Error 2 Any help is appreciated! Thanks, Michael _______________________________________________ linux-dvb users mailing list For V4L/DVB development, please use instead [email protected] [email protected] http://www.linuxtv.org/cgi-bin/mailman/listinfo/linux-dvb