Re: connecting Sony Ericsson T700

hi. please this same list for same issue that you have. wammu do not work
very well it always freeze in some point.
please use terminal commands and gammu --help will give all you want.

2015-08-19 12:31 GMT-03:00 gumb <[email protected]>:

> Hi.
>
> I am trying to connect my Sony Ericsson T700 with Wammu but have no idea
> what many of the settings mean or what I'm required to enter at certain
> steps. I've looked at the Gammu phone database and see a couple of
> entries for this model, but this still doesn't tell me exactly what to
> enter in order to set it up. Note that I can access the phone over USB
> mass storgage in my file manager to do transfers no problem, but this
> doesn't give me easy access to my SMS messages or other items that I'd
> like to get off the phone and archive / access in an easier way.
>
> Firstly, when I connect the phone via USB, I get a choice of 4 modes to
> choose from. Which should I select?
>
> - Phone mode
> - Media transfer
> - Print
> - Mass storage
>
> I've already tried all but the Print option, but still stumble at other
> steps in the phone wizard. If I select 'Guided configuration', I don't
> know what system this phone uses. I select Sony Ericsson, then I don't
> know if I should select AT or OBEX. If I select 'Automatically search
> for a phone', when in USB mass storage mode I get this message:
>
> Wammu is now searching for phone:
> All finished, found 0 phones
> No phone has been found!
>
> I don't know how to find out the device name of the USB port. I noted
> the following output in dmesg after connecting the phone in Phone Mode:
>
> [57602.509277] usb 1-3.1: new high-speed USB device number 15 using
> ehci-pci
> [57602.591406] usb 1-3.1: New USB device found, idVendor=0fce,
> idProduct=d0fb
> [57602.591418] usb 1-3.1: New USB device strings: Mfr=1, Product=2,
> SerialNumber=3
> [57602.591426] usb 1-3.1: Product: Sony Ericsson T700
> [57602.591433] usb 1-3.1: Manufacturer: Sony Ericsson
> [57602.591439] usb 1-3.1: SerialNumber: 3577460270559680
> [57602.783799] cdc_wdm 1-3.1:3.7: cdc-wdm0: USB WDM device
> [57602.784384] usbcore: registered new interface driver cdc_wdm
> [57602.791302] cdc_acm 1-3.1:3.1: ttyACM0: USB ACM device
> [57602.798238] cdc_acm 1-3.1:3.3: ttyACM1: USB ACM device
> [57602.799359] usbcore: registered new interface driver cdc_acm
> [57602.799363] cdc_acm: USB Abstract Control Model driver for USB modems
> and ISDN adapters
> [57602.810452] cdc_ether 1-3.1:3.8 usb0: register 'cdc_ether' at
> usb-0000:00:1a.7-3.1, CDC Ethernet Device, 02:80:37:1a:03:00
> [57602.814071] usbcore: registered new interface driver cdc_ether
>
> So, I tried connecting manually with the device name /dev/ttyACM0 or
> /dev/ttyACM1. I'm told I don't have permission and maybe I need to be in
> the dialout group. Adding myself to that group doesn't help. In USB mass
> storage mode, and after opening (mounting) the phone and phone card in
> my file manager, I note the following in dmesg, followed by a huge
> amount more gobbledegook including error messages that I won't post here:
>
> [58992.667292] usb 1-3.1: new high-speed USB device number 16 using
> ehci-pci
> [58992.825764] usb 1-3.1: New USB device found, idVendor=0fce,
> idProduct=e0fb
> [58992.825776] usb 1-3.1: New USB device strings: Mfr=1, Product=2,
> SerialNumber=3
> [58992.825784] usb 1-3.1: Product: Memory Stick
> [58992.825791] usb 1-3.1: Manufacturer: Sony Ericsson
> [58992.825797] usb 1-3.1: SerialNumber: 3577460270559680
> [58992.828741] usb-storage 1-3.1:2.0: USB Mass Storage device detected
> [58992.828963] scsi11 : usb-storage 1-3.1:2.0
> [58993.833092] scsi 11:0:0:0: Direct-Access     Sony Eri Memory Stick
>       0 PQ: 0 ANSI: 0
> [58993.836116] sd 11:0:0:0: Attached scsi generic sg3 type 0
> [58993.838318] sd 11:0:0:0: [sdc] Attached SCSI removable disk
> [58993.838687] scsi 11:0:0:1: Direct-Access     Sony Eri Memory Stick
>       0 PQ: 0 ANSI: 0
> [58993.838846] sd 11:0:0:1: Attached scsi generic sg4 type 0
> [58993.841583] sd 11:0:0:1: [sdd] Attached SCSI removable disk
> [59002.343566] sd 11:0:0:0: [sdc] 120094 512-byte logical blocks: (61.4
> MB/58.6 MiB)
> [59002.344830] sd 11:0:0:0: [sdc] Test WP failed, assume Write Enabled
> [59002.346196] sd 11:0:0:0: [sdc] Asking for cache data failed
> [59002.346202] sd 11:0:0:0: [sdc] Assuming drive cache: write through
> [59002.347335] sd 11:0:0:1: [sdd] 7815170 512-byte logical blocks: (4.00
> GB/3.72 GiB)
>
> Right at the end of all the blurb that follows I see
> [59013.580201] FAT-fs (sdc1): Volume was not properly unmounted. Some
> data may be corrupt. Please run fsck.
> [59015.304919] FAT-fs (sdd1): Volume was not properly unmounted. Some
> data may be corrupt. Please run fsck.
>
> That at least suggests the device names. If I then try a manual
> connection to /dev/sdc1 or /dev/sdd1 with 'at' or 'at115200' (as noted
> in the database by another user) I'm told I don't have permission and
> maybe I should be in the disk group. Adding myself to that group doesn't
> make any difference either.
>
> I've tried all sorts of variations on all these options but am getting
> nowhere.
>
> All this on openSUSE 13.1 64-bit, KDE 4.11.5 and Wammu 0.36
> Running on Python 2.7.6
> Using wxPython 2.8.12.1
> Using python-gammu 1.33.0 and Gammu 1.33.0
>
>
> ------------------------------------------------------------------------------
> _______________________________________________
> Gammu-users mailing list -
> https://lists.sourceforge.net/lists/listinfo/gammu-users
>



-- 
gilberto dos santos alves
+55(11)9-8646-5049
sao paulo - sp - brasil

------------------------------------------------------------------------------

_______________________________________________
Gammu-users mailing list - https://lists.sourceforge.net/lists/listinfo/gammu-users