Re: AR5418: Abnormal state in AP mode by Madwifi
Mohammad Abdelhadi <[email protected]> Wed, 12 Jan 2011 11:34:01 +0200
| Newsgroups | gmane.linux.drivers.madwifi.user |
|---|---|
| Message-ID | <[email protected]> |
Hi, Try the following steps in order to set your card into Master mode (AP): The interface is ath0 · *sudo service network-manager stop # First, disable the network manager * ** * · sudo wlanconfig ath0 destroy · sudo wlanconfig ath0 create wlandev wifi0 wlanmode ap · sudo iwconfig ath0 essid test # Set the network's essid · sudo iwconfig ath0 channel 1 #Set the channel · sudo ifconfig ath0 up * Hope this helps, Regards -- Mohammad 2011/1/12 Volker <[email protected]> > Hi all, > > I'm trying to configure my wireless card AR5418 as AP mode in Ubuntu 10.10. > I have compiled Madwifi and installed the modules successfully, and it works > well in managed mode. But when I tried to add and configure an interface in > master mode by wlanconfig, it can not be found by other devices. > > My configurations: > Ubuntu 10.10 with Linux 2.6.35-22 i686 > Chipset of wireless card: AR5418 (Mini-PCI-E) > An ethernet card: eth2 > Madwifi: madwifi-trunk-r4132-20101222 > > ****************************** > # iwconfig > lo no wireless extensions. > > eth2 no wireless extensions. > > wifi0 no wireless extensions. > > ath0 IEEE 802.11g ESSID:"wifi-test" > Mode:Master Frequency:2.412 GHz Access Point: > 06:21:63:2F:E3:0C > Bit Rate:0 kb/s Tx-Power:14 dBm Sensitivity=1/1 > Retry:off RTS thr:off Fragment thr:off > Encryption key:off > Power Management:off > Link Quality=0/70 Signal level=-96 dBm Noise level=-96 dBm > Rx invalid nwid:10992 Rx invalid crypt:0 Rx invalid frag:0 > Tx excessive retries:0 Invalid misc:0 Missed beacon:0 > > I don't know why the value of "*Rx invalid nwid*" is increasing all the > time. > > ****************************** > # ifconfig > ath0 Link encap:Ethernet HWaddr 06:21:63:2f:e3:0c > inet addr:192.168.100.1 Bcast:192.168.100.255 > Mask:255.255.255.0 > inet6 addr: fe80::421:63ff:fe2f:e30c/64 Scope:Link > UP BROADCAST MULTICAST MTU:1500 Metric:1 > RX packets:0 errors:0 dropped:0 overruns:0 frame:0 > TX packets:473 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:0 (0.0 B) TX bytes:43583 (43.5 KB) > > eth2 Link encap:Ethernet HWaddr 00:01:80:7a:cc:44 > inet addr:192.168.2.60 Bcast:255.255.255.255 Mask:255.255.255.0 > inet6 addr: fe80::201:80ff:fe7a:cc44/64 Scope:Link > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:114209 errors:0 dropped:0 overruns:0 frame:0 > TX packets:55002 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:55956404 (55.9 MB) TX bytes:6225272 (6.2 MB) > Interrupt:42 Base address:0x2000 > > lo Link encap:Local Loopback > inet addr:127.0.0.1 Mask:255.0.0.0 > inet6 addr: ::1/128 Scope:Host > UP LOOPBACK RUNNING MTU:16436 Metric:1 > RX packets:136 errors:0 dropped:0 overruns:0 frame:0 > TX packets:136 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:0 > RX bytes:11806 (11.8 KB) TX bytes:11806 (11.8 KB) > > wifi0 Link encap:UNSPEC HWaddr > 00-21-63-2F-E3-0C-30-30-00-00-00-00-00-00-00-00 > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:44156 errors:0 dropped:0 overruns:0 frame:10287 > TX packets:32282 errors:7602 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:280 > RX bytes:4494270 (4.4 MB) TX bytes:5266720 (5.2 MB) > Interrupt:18 > ****************************** > # lspci > 03:00.0 Network controller: Atheros Communications Inc. AR5008 Wireless > Network Adapter (rev 01) > > # lsmod > ath_hal 396940 3 ath_rate_sample,ath_pci > ath_pci 179596 0 > ath_rate_sample 11456 1 > ... > wlan 220600 4 wlan_scan_ap,ath_rate_sample,ath_pci > wlan_scan_ap 8417 1 > > ****************************** > My commands: > # ifconfig wifi0 down > # wlanconfig ath0 create wlandev wifi0 wlanmode ap > # iwconfig ath0 essid wifi-test > # iwconfig ath0 channel 1 > # ifconfig ath0 192.168.100.1 > # ifconfig ath0 up > > I did not add options in /etc/modprobe.d/madwifi and > /etc/network/interfaces. > > Can anyone give me some suggestions? Thanks in advance. > > Best regards, > Volker > > > ------------------------------------------------------------------------------ > Protect Your Site and Customers from Malware Attacks > Learn about various malware tactics and how to avoid them. Understand > malware threats, the impact they can have on your business, and how you > can protect your company and customers by using code signing. > http://p.sf.net/sfu/oracle-sfdevnl > _______________________________________________ > Madwifi-users mailing list > [email protected] > https://lists.sourceforge.net/lists/listinfo/madwifi-users > > ------------------------------------------------------------------------------ Protect Your Site and Customers from Malware Attacks Learn about various malware tactics and how to avoid them. Understand malware threats, the impact they can have on your business, and how you can protect your company and customers by using code signing. http://p.sf.net/sfu/oracle-sfdevnl _______________________________________________ Madwifi-users mailing list [email protected] https://lists.sourceforge.net/lists/listinfo/madwifi-users