Re: problem installing driver rtl8139

On Monday 09 December 2002 14:55, you wrote:
> try insmod rtl8139 (without o ) ?

no change !


>
> --- Panard <[email protected]> wrote:
> > Hi !
> >
> > I've a big problem.
> > I've a kernel 2.4.19, and when I make 'insmod
> > rtl8139.o', I've the error :
> > no surch device
> >
> > But, when I make   ./rtl8139-diag -aem, I've the
> > ouput :
> > rtl8139-diag.c:v2.10 9/18/2002 Donald Becker
> > ([email protected])
> >  http://www.scyld.com/diag/index.html
> > Index #1: Found a RealTek RTL8139 adapter at 0xd000.
> > RealTek chip registers at 0xd000
> >  0x000: 96fc5000 00009033 b9f38105 0a00b18d 00002000
> > 00002000 00002000
> > 00002000
> >  0x020: 00001000 00300028 20004000 00000400 81100000
> > 01000000 0000fff0
> > 00000000
> >  0x040: 74400000 00000000 fc161dc7 00000000 004d1000
> > 00000000 0088e51c
> > 0010042c
> >  0x060: 1000000f 01e17809 00000000 00000000 00000704
> > 000003c0 60f60c59
> > 7b732660.
> > Realtek station address 00:50:fc:96:33:90, chip type
> > 'rtl8139C'.
> >   Receiver configuration: Reception disabled
> >      Rx FIFO threshold 16 bytes, maximum burst 16
> > bytes, 8KB ring
> >   Transmitter disabled with normal settings, maximum
> > burst 16 bytes.
> >     Tx entry #0 status 00002000 incomplete, 0 bytes.
> >     Tx entry #1 status 00002000 incomplete, 0 bytes.
> >     Tx entry #2 status 00002000 incomplete, 0 bytes.
> >     Tx entry #3 status 00002000 incomplete, 0 bytes.
> >   Flow control: Tx disabled  Rx disabled.
> >   The chip configuration is 0x10 0x4d, MII
> > full-duplex mode.
> >   No interrupt sources are pending.
> > Decoded EEPROM contents:
> >    PCI IDs -- Vendor 0x10ec, Device 0x8139.
> >    PCI Subsystem IDs -- Vendor 0x10ec, Device
> > 0x8139.
> >    PCI timer settings -- minimum grant 32, maximum
> > latency 64.
> >   General purpose pins --  direction 0xe5  value
> > 0x12.
> >   Station Address 00:50:FC:96:33:90.
> >   Configuration register 0/1 -- 0x4d / 0xc2.
> >  EEPROM active region checksum is 0a28.
> >  The RTL8139 does not use a MII transceiver.
> >  It does have internal MII-compatible registers:
> >    Basic mode control register   0x1000.
> >    Basic mode status register    0x7809.
> >    Autonegotiation Advertisement 0x01e1.
> >    Link Partner Ability register 0x0000.
> >    Autonegotiation expansion     0x0000.
> >    Disconnects                   0x0000.
> >    False carrier sense counter   0x0000.
> >    NWay test register            0x0704.
> >    Receive frame error count     0x0000.
> >
> > Help !
> >
> > Thanks
> >
> > --
>
> ________________________________________________________
>
> >          [email protected]
> > http://www.inzenet.org
> > _______________________________________________
> > realtek mailing list
> > [email protected]
> > http://www.scyld.com/mailman/listinfo/realtek
>
> =====
> Mit freundlichen Gruessen
>
> Patrick Thempel
> mail:[email protected]
>
> __________________________________________________
> Do you Yahoo!?
> Yahoo! Mail Plus - Powerful. Affordable. Sign up now.
> http://mailplus.yahoo.com

-- 
________________________________________________________
         [email protected]                http://www.inzenet.org