0ac8:307b Z-Star Microelectronics Corp. USB 1.1 WebCam

Ciao!
I'm davide from italy (sorry for the grammar),
and i'm trying to activate the webcam Z-Star with the "Jef Moine" 
driver:  gspcav2-2.0.3 <http://moinejf.free.fr/gspcav2-2.0.3.tar.gz>
on the website it seems to work..


The drivers compilation and installation goes well,
the modules loading too,
but the webcam seems doesn't work :-(


I did as advised Jef:


1) - do
                        echo 0x3f > /sys/module/gspca_main/parameters/debug

2) then start the application, and send me the last kernel
                  messages:

usb 2-1: USB disconnect, address 2
gspca: kill transfer
gspca: disconnect complete
usb 2-1: new full speed USB device using uhci_hcd and address 4
usb 2-1: configuration #1 chosen from 1 choice
gspca: probing 0ac8:307b
zc3xx: probe 2wr ov vga 0x0000
zc3xx: probe 3wr vga 1 0x4001
zc3xx: probe 3wr vga type 29
zc3xx: probe sensor -> 29
zc3xx: Find Sensor GC0305
gspca: probe ok
usb 2-1: New USB device found, idVendor=0ac8, idProduct=307b
usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: Product: PC Camera
usb 2-1: Manufacturer: Vimicro Corp.
gspca: hald-probe-vide open
gspca: open done
gspca: querycap
gspca: querycap
gspca: enum fmt cap
gspca: try fmt cap JPEG 10000x10000
gspca: hald-probe-vide close
gspca: close done
type=1400 audit(1214479558.547:132): avc:  denied  { syslog_read } for  
pid=2975 comm="dmesg" 
scontext=unconfined_u:system_r:hotplug_t:s0-s0:c0.c1023 
tcontext=system_u:system_r:kernel_t:s0 tclass=system


gspca: disconnect complete
usb 2-1: new full speed USB device using uhci_hcd and address 5
usb 2-1: configuration #1 chosen from 1 choice
gspca: probing 0ac8:307b
zc3xx: probe 2wr ov vga 0x0000
zc3xx: probe 3wr vga 1 0x4001
zc3xx: probe 3wr vga type 29
zc3xx: probe sensor -> 29
zc3xx: Find Sensor GC0305
gspca: probe ok
usb 2-1: New USB device found, idVendor=0ac8, idProduct=307b
usb 2-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
usb 2-1: Product: PC Camera
usb 2-1: Manufacturer: Vimicro Corp.
gspca: hald-probe-vide open
gspca: open done
gspca: querycap
gspca: querycap
gspca: enum fmt cap
gspca: try fmt cap JPEG 10000x10000
gspca: hald-probe-vide close
gspca: close done


and the run "./grab": http://www.cosmogonia.org/cosmogoniA/tmp/toto.jpg
and dmesg:

gspca: grab open
gspca: open done
gspca: querycap
gspca: set fmt cap JPEG 640x480
gspca: try fmt cap JPEG 640x480
gspca: reqbufs 4
gspca: frame alloc frsz: 307200
gspca: new fr_sz: 94208
gspca: reqbufs st:0 c:4
gspca: querybuf
gspca: mmap start:b80e7000 size:94208
gspca: querybuf
gspca: mmap start:b80c9000 size:94208
gspca: querybuf
gspca: mmap start:b80b2000 size:94208
gspca: querybuf
gspca: mmap start:b809b000 size:94208
gspca: stream on
gspca: init transfer alt 7
gspca: use ISOC alt 6 ep 0x81
gspca: isoc 32 pkts size 768 (bsize:24576)
zc3xx: gamma:4 contrast:128 gamma coeff: 0/128
zc3xx: tb: 13 38 59 79 92 a7 b9 c8
zc3xx:     d4 df e7 ee f4 f9 fc ff
zc3xx:     26 22 20 1c 16 13 10 0d
zc3xx:     0b 09 07 06 05 04 03 02
gspca: stream on OK JPEG 640x480
gspca: stream off
gspca: kill transfer
gspca: stream off OK
gspca: grab close
gspca: frame free
gspca: close done

could yu give me any suggestion? :-)

thanks a lot!!



-- 


cosmogoniA <http://www.cosmogonia.org/>
noprovarenofareononfarenonc'èprovare

-------------------------------------------------------------------------
Check out the new SourceForge.net Marketplace.
It's the best place to buy or sell services for
just about anything Open Source.
http://sourceforge.net/services/buy/index.php

_______________________________________________
Spca50x-devs mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/spca50x-devs