3c900 combo problem

Hi, I have this net card. I use linux kernel 2.4.20. I have problem:

3c59x: Donald Becker and others. www.scyld.com/network/vortex.html
See Documentation/networking/vortex.txt
00:0e.0: 3Com PCI 3c900 Boomerang 10Mbps Combo at 0xe000. Vers LK1.1.16
 00:10:4b:95:47:52, IRQ 11
  product code 4d50 rev 00.0 date 04-15-98
  Internal config register is 302d8, transceivers 0xe138.
  8K word-wide RAM 3:5 Rx:Tx split, 10baseT interface.
00:0e.0:  Media override to transceiver type 3 (10base2).
  Enabling bus-master transmits and whole-frame receives.
00:0e.0: scatter/gather enabled. h/w checksums disabled
eth0:  Filling in the Rx ring.
eth0: Media override to transceiver 3 (10base2).
eth0: Initial media type 10base2.
vortex_up(): writing 0x3302d8 to InternalConfig
eth0: vortex_up() InternalConfig 003302d8.
eth0: vortex_up() irq 11 media status 0800.
boomerang_start_xmit()
eth0: Trying to send a packet, Tx index 0.
eth0: Media selection timer tick happened, 10base2.
dev->watchdog_timeo=500
eth0: Media selection timer finished, 10base2.
boomerang_start_xmit()
eth0: Trying to send a packet, Tx index 1.
boomerang_start_xmit()
eth0: Trying to send a packet, Tx index 2.
eth0: Media selection timer tick happened, 10base2.
dev->watchdog_timeo=500
eth0: Media selection timer finished, 10base2. 
oop, status 8401.
boomerang_interrupt->boomerang_rx
boomerang_rx(): status 8001
Receiving packet size 250 status 80fa.
Receiving packet size 92 status 805c.
Receiving packet size 92 status 805c.
eth0: In interrupt loop, status 8c01.
boomerang_interrupt->boomerang_rx
boomerang_rx(): status 8801
Receiving packet size 78 status 804e.
Receiving packet size 78 status 804e.
Receiving packet size 60 status 803c.
Receiving packet size 92 status 805c.
eth0: In interrupt loop, status 8401.
boomerang_interrupt->boomerang_rx
boomerang_rx(): status 8001
 Rx error: status 01.
eth0: exiting interrupt, status 8000.
  Flags; bus-master 1, dirty 64(0) current 64(0)
  Transmit list 00000000 vs. d7562200.
  0: @d7562200  length 80000062 status 00000062
  1: @d7562240  length 80000062 status 00000062
  2: @d7562280  length 80000062 status 00000062
  3: @d75622c0  length 80000062 status 00000062
  4: @d7562300  length 80000062 status 00000062
  5: @d7562340  length 80000062 status 00000062
  6: @d7562380  length 80000062 status 00000062
  7: @d75623c0  length 80000062 status 00000062
  8: @d7562400  length 80000062 status 00000062
  9: @d7562440  length 80000062 status 00000062
  10: @d7562480  length 80000062 status 00000062
  11: @d75624c0  length 80000062 status 00000062
  12: @d7562500  length 80000062 status 00000062
  13: @d7562540  length 80000062 status 00000062
  14: @d7562580  length 80000062 status 80000062
  15: @d75625c0  length 80000062 status 80000062
eth0: Resetting the Tx ring pointer. 

What this means? I don't have any problem with IRQ(all is disabled in BIOS):
           CPU0       
  0:      13291    IO-APIC-edge  timer
  1:        495    IO-APIC-edge  keyboard
  2:          0          XT-PIC  cascade
  9:          0    IO-APIC-edge  acpi
 11:          0   IO-APIC-level  eth0
 14:       1373    IO-APIC-edge  ide0
NMI:          0 
LOC:      13244 
ERR:          0
MIS:          0 

Pings are >18000ms.
Thx...

-- 
__________________________________________________________
Sign-up for your own FREE Personalized E-mail at Mail.com
http://www.mail.com/?sr=signup

_______________________________________________
vortex mailing list
[email protected]
http://www.scyld.com/mailman/listinfo/vortex