Trouble with PVR150 and FC4

Hey guys, I'm having some trouble w/ my Hauppauge 150.  I did the FC4
install, but getting static.  Here's some info:

Using wilsonet.com's FC4 how-to.  Everything went fine until I tried
testing the PVR-150 I have.  (Section 10 of wilson's how-to)


I ran the ivtv install w/ no problem, added the NTSC entry into the
/etc/modprobe.conf, and ran "depmod -ae" and "modprobe ivtv" w/ no
errors.

Here's the ivtv content from /var/log/messages :


Nov 17 20:11:28 localhost kernel: ivtv:  ==================== START
INIT IVTV ====================
Nov 17 20:11:28 localhost kernel: ivtv:  version 0.4.0 (tagged release) loading

Nov 17 20:11:28 localhost kernel: ivtv:  Linux version:
2.6.14-1.1637_FC4 686 REGPARM 4KSTACKS gcc-4.0
Nov 17 20:11:28 localhost kernel: ivtv:  In case of problems please
include the debug info
Nov 17 20:11:28 localhost kernel: ivtv:  between the START INIT IVTV
and END INIT IVTV lines when

Nov 17 20:11:29 localhost fstab-sync[2574]: removed all generated mount points
Nov 17 20:11:29 localhost kernel: ivtv:  mailing the ivtv-devel mailinglist.
Nov 17 20:11:29 localhost kernel: ivtv0: Autodetected WinTV PVR 150
card (iTVC16 based)

Nov 17 20:11:29 localhost kernel: ACPI: PCI Interrupt Link [LNK4]
enabled at IRQ 3
Nov 17 20:11:29 localhost kernel: PCI: setting IRQ 3 as level-triggered
Nov 17 20:11:29 localhost kernel: ACPI: PCI Interrupt 0000:02:
07.0[A] -> Link [LNK4] -> GSI 3 (level, low) -> IRQ 3
Nov 17 20:11:29 localhost kernel: ivtv0: Unreasonably low latency
timer, setting to 64 (was 32)
Nov 17 20:11:29 localhost kernel: ivtv0: i2c attach to card #0 ok
[client=tveeprom, addr=50]

Nov 17 20:11:29 localhost kernel: tveeprom 2-0050: Hauppauge model
26032, rev C199, serial# 2985049
Nov 17 20:11:29 localhost kernel: tveeprom 2-0050: tuner model is TCL
2002N 5H (idx 99, type 50)
Nov 17 20:11:29 localhost kernel: tveeprom 2-0050: TV standards
NTSC(M) (eeprom 0x08)

Nov 17 20:11:29 localhost kernel: tveeprom 2-0050: audio processor is
CX25841 (idx 35)
Nov 17 20:11:29 localhost kernel: tveeprom 2-0050: decoder processor
is CX25841 (idx 28)
Nov 17 20:11:29 localhost kernel: tveeprom 2-0050: has no radio, has IR remote

Nov 17 20:11:29 localhost kernel: tuner 2-0061: chip found @ 0xc2
(ivtv i2c driver #0)
Nov 17 20:11:29 localhost kernel: ivtv0: i2c attach to card #0 ok
[client=(tuner unset), addr=61]
Nov 17 20:11:29 localhost kernel: cx25840 2-0044: cx25841-23 found @
0x88 (ivtv i2c driver #0)

Nov 17 20:11:29 localhost kernel: cx25840 2-0044: loaded
/lib/modules/HcwMakoA.ROM firmware (13353 bytes)
Nov 17 20:11:29 localhost kernel: ivtv0: i2c attach to card #0 ok
[client=cx25840, addr=44]
Nov 17 20:11:29 localhost kernel: wm8775 2-001b: chip found @ 0x36
(ivtv i2c driver #0)

Nov 17 20:11:29 localhost kernel: ivtv0: i2c attach to card #0 ok
[client=wm8775, addr=1b]
Nov 17 20:11:29 localhost kernel: ivtv0: loading /lib/modules/ivtv-fw-enc.bin
Nov 17 20:11:29 localhost kernel: ivtv0: Encoder revision: 0x02040024

Nov 17 20:11:29 localhost kernel: ivtv0 warning: Encoder Firmware can
be buggy, use version 0x02040011 or 0x02050032.
Nov 17 20:11:29 localhost kernel: ivtv0: Allocate DMA encoder MPEG
stream: 128 x 32768 buffers (4096KB total)

Nov 17 20:11:29 localhost kernel: ivtv0: Allocate DMA encoder YUV
stream: 194 x 10800 buffers (2048KB total)
Nov 17 20:11:29 localhost kernel: ivtv0: Allocate DMA encoder VBI
stream: 120 x 17472 buffers (2048KB total)

Nov 17 20:11:29 localhost kernel: ivtv0: Allocate DMA encoder PCM
audio stream: 455 x 4608 buffers (2048KB total)
Nov 17 20:11:29 localhost kernel: tuner 2-0061: type set to 50 (TCL 2002N)
Nov 17 20:11:29 localhost kernel: ivtv0: Initialized WinTV PVR 150, card #0

Nov 17 20:11:29 localhost kernel: ivtv:  ====================  END
INIT IVTV  ====================

lspci -v

02:07.0 Multimedia video controller: Internext Compression Inc iTVC16
(CX23416) MPEG-2 Encoder (rev 01)
        Subsystem: Hauppauge computer works Inc. WinTV PVR 150

        Flags: bus master, medium devsel, latency 64, IRQ 3
        Memory at e4000000 (32-bit, prefetchable) [size=64M]

        Capabilities: [44] Power Management version 2


ls -ltr /dev/video*
crw-------  1 mythtv root 81,  0 Nov 17 15:11 /dev/video0

lrwxrwxrwx  1 root   root      6 Nov 17 15:11 /dev/video -> video0
crw-------  1 mythtv root 81, 32 Nov 17 15:11 /dev/video32

crw-------  1 mythtv root 81, 24 Nov 17 15:11 /dev/video24

dmesg | grep Initialized


ivtv0: Initialized WinTV PVR 150, card #0

Then I ran


/usr/bin/ivtvctl -u 0x3000
/usr/bin/ivtvctl -p 6
/usr/bin/ivtvctl -f width=720,height=480


mplayer -vo xv /dev/video0

And all I get is static.  And not 'kind of picture' static, but just
all static (even the sound was just static).  I tried different -p
options.  0-6 gives me a dark gray screen, 6 & 7 give me the same sort
of static.


I know the cable line isn't the problem (I can see the channels when I
plug it directly into the TV).  Any ideas.

Note:  I don't have /usr/lib/ivtv/ptune-ui.pl in my system.  Anyone
know if this might solve the problem or where I might grab a version?


~sean