Re: problems with PowerBook G4

Yes, it turns out that is the problem! The router somehow got 
misconfigured as 0.0.0.0 instead of 10.0.1.1.
here is ifconfig:
bond0     Link encap:Ethernet  HWaddr 00:00:00:00:00:00
           BROADCAST MASTER MULTICAST  MTU:1500  Metric:1
           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:0
           RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

dummy0    Link encap:Ethernet  HWaddr 86:DB:59:06:1D:3C
           BROADCAST NOARP  MTU:1500  Metric:1
           RX packets:0 errors:0 dropped:0 overruns:0 frame:0
           TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:0
           RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

eth0      Link encap:Ethernet  HWaddr 00:03:93:80:24:F2
           inet addr:10.0.1.200  Bcast:10.255.255.255  Mask:255.255.255.0
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:17 errors:0 dropped:0 overruns:0 frame:0
           TX packets:16 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:1000
           RX bytes:1374 (1.3 Kb)  TX bytes:1174 (1.1 Kb)
           Interrupt:41 Base address:0x7400

eth1      Link encap:Ethernet  HWaddr 00:30:65:16:B7:DD
           inet addr:10.0.1.12  Bcast:10.255.255.255  Mask:255.255.255.0
           UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
           RX packets:22 errors:0 dropped:0 overruns:0 frame:0
           TX packets:20 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:1000
           RX bytes:1910 (1.8 Kb)  TX bytes:3002 (2.9 Kb)
           Interrupt:57

lo        Link encap:Local Loopback
           inet addr:127.0.0.1  Mask:255.0.0.0
           UP LOOPBACK RUNNING  MTU:16436  Metric:1
           RX packets:4 errors:0 dropped:0 overruns:0 frame:0
           TX packets:4 errors:0 dropped:0 overruns:0 carrier:0
           collisions:0 txqueuelen:0
           RX bytes:280 (280.0 b)  TX bytes:280 (280.0 b)

and route -n:
Kernel IP routing table
Destination     Gateway         Genmask         Flags   MSS Window  
irtt Iface
10.0.1.0        *               255.255.255.0   U         0 0          
0 eth0
10.0.1.0        *               255.255.255.0   U         0 0          
0 eth1
loopback        localhost       255.0.0.0       UG        0 0          
0 lo

Is the right command to use 10.0.1.1 as a router (for both eth1 and 
eth0) 'route add default gw 10.0.1.1'? Or is it something else? That is 
what I got from manning route, but I don't what to mess anything up by 
having conflicting IP addresses.
thanks
nick
On Sep 22, 2005, at 4:29 AM, Matti Bickel wrote:

> Nicholas S-A <[email protected]> wrote:
>> The output is actually this error from 'man connect':
>> [ENETUNREACH]      The network isn't reachable from this host.
>
> Since you can reach your router: have you checked *which* interface
> reaches the router?
> What's the output of route -n?
>
> Sorry, just a wild guess.
> Matti
> -- 

-- 
[email protected] mailing list