Re: unofficial/unsupported storage upgrade to old PE2900?

Rene Shuster <[email protected]>
Newsgroups gmane.linux.hardware.dell.poweredge
Message-ID <CADTU-KmLD8tR3ixoZL2=rYZM_ftfDwJPHaTkKNjQLQTB+QaV7g@mail.gmail.com>
correction:
DELL uses SFF-8484 to connect to the DELL backplane and SFF-8087 is used to
connect to the LSI 9211-4i. Not sure what the PERC H700 uses. The 6/i uses
SFF-8484 as well.

On Mon, Oct 26, 2015 at 9:30 AM, Rene Shuster <[email protected]>
wrote:

> Interesting. I would be interested, too. However keep in mind that the
> PE2900/2950 is PCIe 1.0 while DELL PERC 7th gen are PCIe 2.0 accd. to
> http://www.dell.com/learn/us/en/19/campaigns/dell-raid-controllers
>
> Now I was able to frankenstein a LSI 9211-4i into a PE2900 and re-use a
> SFF cable from a decommissioned PE840 (yuk!).
> To utilize all 6 drive slots you probably need a 9211-8i. The 9211-4i is
> $89 at SCSI4me (
> http://www.scsi4me.com/lsi-logic-sas-9211-4i-low-profile-four-port-6gb-s-sata-and-sas-pcie-hba-with-integrated-raid.html
> ).
> It's not a production server, so I can't tell how it goes under load or in
> the long run. I just needed to update SAS drive firmware for non-DELL
> drives and the Seagate firmwre updater needed the drives in
> JBOD/Pass-through mode which is something the DELL PERC do not offer.
>
> From that experience all I can tell is that you need to make sure you got
> the correct cable, the right connector shape (90º or straight), and the
> right cable length. Here's some pictures and a overview of SAS connectors:
> https://en.wikipedia.org/wiki/Serial_attached_SCSI#Connectors
> DELL uses SFF-8087 to connect to the DELL backplane and SFF-8484 is used
> to connect to the LSI 9211-4i. Not sure what the PERC H700 uses. The 6/i
> uses SFF-8087 as well.
>
>
> On Fri, Oct 23, 2015 at 12:32 PM, Bond Masuda <[email protected]>
> wrote:
>
>> I recall reading somewhere in the past that people have upgraded old PE
>> 2900 servers from a PERC 6/i to PERC H700 in order to install > 2TB hard
>> drives in the PE 2900. If my recollection is correct, all that was
>> needed as a SFF-8087 to SFF-8484 cable. Anyone here try similar
>> upgrades? Any experience with the newer controllers than the H700? H710?
>>
>> I'm looking to upgrade my 2900, so just wanted to see what other
>> unofficial/unsupported options are out there that people have tried with
>> success (or failure - so I should avoid)?
>>
>> Thx.
>>
>> _______________________________________________
>> Linux-PowerEdge mailing list
>> [email protected]
>> https://lists.us.dell.com/mailman/listinfo/linux-poweredge
>>
>
>
>
> --
> Tech III * AppControl * Endpoint Protection * Server Maintenance
> Buncombe County Schools Technology Department Network Group
> ComicSans Awareness Campaign <http://comicsanscriminal.com>
>



-- 
Tech III * AppControl * Endpoint Protection * Server Maintenance
Buncombe County Schools Technology Department Network Group
ComicSans Awareness Campaign <http://comicsanscriminal.com>

_______________________________________________
Linux-PowerEdge mailing list
[email protected]
https://lists.us.dell.com/mailman/listinfo/linux-poweredge
lmpx.com only provides a reader for public news (NNTP) servers. It is not affiliated with the servers or forums shown here and is not responsible for the content of articles, which is written by their respective authors.