Re: Agilent 82357B repeatable hard failure

Thanks - all the runs look good except of course the R&S NRVD.
@Jim - the IBEOS ioctl failed could be due to a set-bin=1 option for the
board in your gpib.conf file.
           The agilent_82357 does not support 8 bit compares.
What is the general opinion as to whether the ATN workaround should be
pushed to the SVN ?
-Dave

On Fri, 29 Sept 2023 at 02:58, Jim Houston <[email protected]> wrote:

> Hi Dave,Everyone
>
> I ran the onebyte2 test against both the SVN kernel and the patched kernel
> the output follows.  I'm getting failures on IBEOS ioctl.  I'm still
> looking at
> this and I may send another email if I figure it out.  I did a fresh
> install and
> I may have broken something in the process.
>
> JIm Houston
>
> Test with current SVN kernel:
>
> jhouston@gpib-test2:~/onebyte$ ./onebyte2 -d 22 s
>   0x0168 ibwrt
> + 0x0138 ibrd dev
> libgpib: IBEOS ioctl failed
> 0 0x0130 ibrd board
> libgpib: IBEOS ioctl failed
> 0 0x0130 ibrd board
> libgpib: IBEOS ioctl failed
> . 0x013c ibrd board
> libgpib: IBEOS ioctl failed
> 0 0x0130 ibrd board
> libgpib: IBEOS ioctl failed
> 0 0x0130 ibrd board
> libgpib: IBEOS ioctl failed
> 0 0x0130 ibrd board
> libgpib: IBEOS ioctl failed
> 9 0x0130 ibrd board
> libgpib: IBEOS ioctl failed
> E 0x01a4 ibrd board
> libgpib: IBEOS ioctl failed
> - 0x0134 ibrd board
> libgpib: IBEOS ioctl failed
> 3 0x0138 ibrd board
> libgpib: IBEOS ioctl failed
>  0x0124 ibrd board
> libgpib: IBEOS ioctl failed
>
>  0x2128 ibrd board
> jhouston@gpib-test2:~/onebyte$
>
> With patched kernel:
>
> jhouston@gpib-test2:~/onebyte$ ./onebyte2 -d 22 s
>   0x0128 ibwrt
> 0 0x0174 ibrd dev
> libgpib: IBEOS ioctl failed
> . 0x0174 ibrd board
> libgpib: IBEOS ioctl failed
> 0 0x0174 ibrd board
> libgpib: IBEOS ioctl failed
> 0 0x0174 ibrd board
> libgpib: IBEOS ioctl failed
> 0 0x0174 ibrd board
> libgpib: IBEOS ioctl failed
> 7 0x0174 ibrd board
> libgpib: IBEOS ioctl failed
> E 0x0174 ibrd board
> libgpib: IBEOS ioctl failed
> - 0x0174 ibrd board
> libgpib: IBEOS ioctl failed
> 3 0x0174 ibrd board
> libgpib: IBEOS ioctl failed
>  0x0174 ibrd board
> libgpib: IBEOS ioctl failed
>
>  0x2174 ibrd board
> jhouston@gpib-test2:~/onebyte$
>
>
> On 9/28/23 13:13, dave penkler wrote:
>
> Hi Jim,
> Please find attached a new version of onebyte to check that board level
> reads work after setting ATN at the end of the read.
> The attached patch for the driver is against the current SVN and sets ATN
> at the end of the read as you proposed.
> @MichaelK you might try this one on the R&S power meter.
> It worked on my Beiming clone:
> In the ibsta 0x174 = CMPL | REM | CIC | ATN | LACS  we see the ATN bit set.
> $ onebyte2 -d8
>   0x0168 ibwrt
> H 0x0174 ibrd dev
> E 0x0174 ibrd board
> W 0x0174 ibrd board
> L 0x0174 ibrd board
> E 0x0174 ibrd board
> T 0x0174 ibrd board
> T 0x0174 ibrd board
> - 0x0174 ibrd board
> P 0x0174 ibrd board
> A 0x0174 ibrd board
> C 0x0174 ibrd board
> K 0x0174 ibrd board
> A 0x0174 ibrd board
> R 0x0174 ibrd board
> D 0x0174 ibrd board
> , 0x0174 ibrd board
> E 0x0174 ibrd board
> 3 0x0174 ibrd board
> 6 0x0174 ibrd board
> 3 0x0174 ibrd board
> 1 0x0174 ibrd board
> A 0x0174 ibrd board
> , 0x0174 ibrd board
> 0 0x0174 ibrd board
> , 0x0174 ibrd board
> 2 0x0174 ibrd board
> . 0x0174 ibrd board
> 1 0x0174 ibrd board
> - 0x0174 ibrd board
> 5 0x0174 ibrd board
> . 0x0174 ibrd board
> 0 0x0174 ibrd board
> - 0x0174 ibrd board
> 1 0x0174 ibrd board
> . 0x0174 ibrd board
> 0 0x0174 ibrd board
>
>  0x2174 ibrd board
> Cheers,
> -Dave
>
>
> On Thu, 28 Sept 2023 at 17:59, dave penkler <[email protected]> wrote:
>
>> Hi Jim,
>> Can you please let us know if the removal of TCS in the SVN works for
>> your reading of the calibration data.
>> I have thought some more about your proposal to set ATN at the end of the
>> read. We just need to verify that board level reads after the first device
>> level read still work with the ATN workaround.
>> If it does that would give us a reliable board level ibsta, From the
>> logic analyser traces it looks like the board gives valid ADSR responses
>> when it is in the Talker Active state i.e. after ibwrt.
>> -Dave
>>
>
>

_______________________________________________
Linux-gpib-general mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/linux-gpib-general