Re: multiple ultramonkeys

I was able to get the document that is stored on RealServer3 and
RealServer4 using two different UltraMonkey machines with each UltraMonkey
on a different network 172.16.X.0 and 172.16.Y.0.  My new challenge is to
use only one UltraMonkey machine (172.16.X.10) to load balance between
RealServer1 (172.16.X.1) and RealServer2 (172.16.X.2) then redirect that
traffic to the same Ultramonkey (172.16.X.10) machine which will then load
balance between RealServer3 (172.16.X.3) and RealServer4 (172.16.X.4).  Is
this possible?  I am having problems (I get a bad gateway error) and I
can't determine if it is a network issue or an UltraMonkey limitation.
Therefore the drawing will be as follows:
                 ----------
                 | Client |
                 ----------
                     |
                     |
              ----------------
 ------------ | Ultramonkey1 | ------------
 |            ----------------            |
 |                  /\                    |
 |   ---------------  ---------------     |
 |   | RealServer1 |  | RealServer2 |     |
 |   ---------------  ---------------     |
 |                \    /                  |
 |                 \  /                   |
 |                  \/                    |
 |                   ----------------------
 |
 |
  ---------------
                |
               / \
 ---------------  ---------------
 | RealServer3 |  | RealServer4 |
 ---------------  ---------------


                                                                           
             Horms                                                         
             <[email protected].                                             
             au>                                                        To 
             Sent by: news             [email protected]   
             <[email protected]                                          cc 
             rg>                                                           
                                                                   Subject 
                                       Re: multiple ultramonkeys           
             11/16/2005 02:02                                              
             AM                                                            
                                                                           
                                                                           
             Please respond to                                             
             ultramonkey-users                                             
             @ultramonkey.org                                              
                                                                           
                                                                           




Mark Brosius <[email protected]> wrote:
>
> Below is a drawing of what I want to do.  The information the Client
wants
> is on RealServer3 or RealServer4.  Is this possible?  Thanks.

If it is on both RealServer3 and RealServer4, then yes.
If it is only on RealServer3 or RealServer4, then no,
unless ultramonkey can work out which of RealServer3 or RealServer4
to use based on IP address and port information, which
is probably not the case.

>
>           ----------
>           | Client |
>           ----------
>               |
>               |
>        ----------------
>        | Ultramonkey1 |
>        ----------------
>               /\
> ---------------  ---------------
> | RealServer1 |  | RealServer2 |
> ---------------  ---------------
>             \    /
>              \  /
>               \/
>        ----------------
>        | UltramonkeyX | (this is either the same Ultramonkey machine as
> above or a new one)
>        ----------------
>               /\
> ---------------  ---------------
> | RealServer3 |  | RealServer4 |
> ---------------  ---------------

--
Horms


--
Ultra Monkey - http://www.ultramonkey.org/
To UNSUBSCRIBE, email to [email protected], with a body:
unsubscribe ultramonkey-users [email protected]
where "[email protected]" is YOUR email address.




This communication, including any attachments, may contain privileged or
confidential information.  It is intended for a specific individual and
purpose and is protected by law.  If you have received this communication
in error, please immediately notify me and destroy the communication.  Any
wrongful interception, disclosure, copying or distribution of this
communication, or the taking of any action based on this communication by
anyone other than the intended recipient is strictly prohibited and
punishable under federal law.


-- 
Ultra Monkey - http://www.ultramonkey.org/
To UNSUBSCRIBE, email to [email protected], with a body:
unsubscribe ultramonkey-users [email protected]
where "[email protected]" is YOUR email address.