Re: heartbeat problem???
Maxence Rousseau <[email protected]>
| Newsgroups | gmane.linux.highavailability.ultramonkey |
|---|---|
| Message-ID | <[email protected]> |
Hello, You must never remove the both heartbeat cable, it's just mean that the other host is down (if you want really remove them, use eth0 & eth2 too in ha.cf)... That's why the documentation suggest to use a serial link. (a crossover cable isn't very far of a serial link) Cheers, Le lundi 12 juin 2006 à 21:52 +0800, Jiang a écrit : > Hi, > > I am not sure if this is the right place to post this message... > anyway... I hv posted it at HA and LVS' mailing list, but seems no > body could answer me... > > In short, I hv two linux machines used to do LVS with HA (all > necessary packages were downloaded from ultramonkey). I have enslaved > eth0 and eth2 for data connections, eth1 and eth3 are for heartbeat, > they are connecting to the other machine > through cross cables. I attached ifconfig result at the end of this email. > > in ha.cf, I have: > *********************************************************************************************** > ucast eth1 172.16.1.1 > ucast eth3 172.16.2.1 > *********************************************************************************************** > In my test, when disconnected both heartbeat cables, the two nodes > became two masters, but the problem happened when I connected > heartbeat cables back, none of the masters were willing to shudown, > which resulted two master running. And I also noticed that data began > to flush the ports(eth0/eth2), which slowed down the network speed > dramaticaly. > > If anybody experienced the same problem or if I have missed something? > I have encounted the problem at least twice in my tests, and I have to > restart my server each time. > > Thanks! > > ifconfig -a: > *********************************************************************************************** > bond0 Link encap:Ethernet HWaddr 00:17:A4:3B:79:6C > inet addr:10.226.200.211 Bcast:10.226.200.255 Mask:255.255.255.0 > UP BROADCAST RUNNING MASTER MULTICAST MTU:1500 Metric:1 > RX packets:10919145 errors:5348955 dropped:0 overruns:0 frame:2 > TX packets:5445539 errors:2071 dropped:0 overruns:0 carrier:2071 > collisions:252799 txqueuelen:0 > RX bytes:720982816 (687.5 Mb) TX bytes:359657582 (342.9 Mb) > > eth0 Link encap:Ethernet HWaddr 00:17:A4:3B:79:6C > inet addr:10.226.200.211 Bcast:10.226.200.255 Mask:255.255.255.0 > UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 > RX packets:5459572 errors:5348954 dropped:0 overruns:0 frame:1 > TX packets:2577877 errors:0 dropped:0 overruns:0 carrier:0 > collisions:123370 txqueuelen:1000 > RX bytes:360491466 (343.7 Mb) TX bytes:170263908 (162.3 Mb) > Interrupt:28 > > eth1 Link encap:Ethernet HWaddr 00:17:A4:3B:79:6B > inet addr:172.16.1.1 Bcast:172.16.1.255 Mask:255.255.255.0 > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:1030 errors:0 dropped:0 overruns:0 frame:0 > TX packets:1286 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:194654 (190.0 Kb) TX bytes:215134 (210.0 Kb) > Interrupt:29 > > eth2 Link encap:Ethernet HWaddr 00:17:A4:3B:79:6C > inet addr:10.226.200.211 Bcast:10.226.200.255 Mask:255.255.255.0 > UP BROADCAST RUNNING SLAVE MULTICAST MTU:1500 Metric:1 > RX packets:5459573 errors:1 dropped:0 overruns:0 frame:1 > TX packets:2867662 errors:2071 dropped:0 overruns:0 carrier:2071 > collisions:129429 txqueuelen:1000 > RX bytes:360491350 (343.7 Mb) TX bytes:189393674 (180.6 Mb) > Base address:0x6000 Memory:f7fe0000-f8000000 > > eth3 Link encap:Ethernet HWaddr 00:11:0A:5E:2C:A9 > inet addr:172.16.2.1 Bcast:172.16.2.255 Mask:255.255.255.0 > UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 > RX packets:1367 errors:0 dropped:0 overruns:0 frame:0 > TX packets:1419 errors:0 dropped:0 overruns:0 carrier:0 > collisions:0 txqueuelen:1000 > RX bytes:253011 (247.0 Kb) TX bytes:254905 (248.9 Kb) > Base address:0x6040 Memory:f7f60000-f7f80000 > *********************************************************************************************** > > Best regards, > - Jiang - > -- Ultra Monkey - http://www.ultramonkey.org/ To UNSUBSCRIBE, email to [email protected], with a body: unsubscribe ultramonkey-users [email protected] where "[email protected]" is YOUR email address.