Can not get WUSB64G working!!

I have the Linksys Wireless-G USB Network Adapter ( WUSB54G ) and im
trying to get this installed on Gentoo, Here is some information I
gotten for review:

$ dmesg
usb 2-1: new full speed USB device using ohci_hcd and address 19
driverloader: stack=8192/60/0 PREEMPT
driverloader: wusb20xp.sys: 0xe0cdc000..0xe0d2e520 entry = e0cf7ebf
(pbase = 0x10000)
eth2: WPA, AES, TKIP, WEP128, WEP64 supported
eth2: Linksys Wireless-G USB Network Adapter at 0000:00:02.11 (MAC
address 00:0F:66:16:BD:A8) ready
eth2: New link status: Disconnected (0002)
usbcore: registered new driver driverloader

$ iwconfig eth2
eth2      IEEE 802.11g  ESSID:""  Nickname:"unknown"
          Mode:Managed  Bit Rate=2 Mb/s  
          RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

$ iwconfig eth2 key open xxxxxxxxxxxxxxxxxxxxxxxxxx
$ iwconfig eth2 essid xxxxxxxx
$ ifconfig eth2 inet 192.168.0.252 netmask 255.255.255.0 broadcast
192.168.0.255

$ iwconfig eth2
eth2      IEEE 802.11g  ESSID:"xxxxxxxx"  Nickname:"unknown"
          Mode:Managed  Bit Rate=2 Mb/s  
          RTS thr:off   Fragment thr:off
          Encryption key:xxxx-xxxx-xxxx-xxxx-xxxx-xxxx-xx   Security
mode:open
          Power Management:off
          Link Quality:0  Signal level:0  Noise level:0
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0

$ ifconfig eth2
eth2   Link encap:Ethernet  HWaddr 00:0F:66:16:BD:A8 
          inet addr:192.168.0.252  Bcast:192.168.0.255  Mask:255.255.255.0
          UP BROADCAST MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)

$ ping -I eth2 192.168.0.1
PING 192.168.0.1 (192.168.0.1) from 192.168.0.252 eth2: 56(84) bytes of
data.
>From 192.168.0.252 icmp_seq=1 Destination Host Unreachable
>From 192.168.0.252 icmp_seq=2 Destination Host Unreachable
>From 192.168.0.252 icmp_seq=3 Destination Host Unreachable
>From 192.168.0.252 icmp_seq=5 Destination Host Unreachable
>From 192.168.0.252 icmp_seq=6 Destination Host Unreachable
>From 192.168.0.252 icmp_seq=7 Destination Host Unreachable

--- 192.168.0.1 ping statistics ---
7 packets transmitted, 0 received, +6 errors, 100% packet loss, time 6014ms