Re: TP-LINK External Serial Modem

"Jacques Goldberg" <[email protected]> escribió:

> You are right.
>
> I had not understood that you continue to use the modem associated  
> with /dev/ttySL0
>
> Please send me a copy of the file /etc/wvdial.conf   which you use  
> to connect  using ttySL0
i have the 2 configuration in the same file wvdial.conf this is the  
configuration of the external modem tp-link

[Dialer Defaults]
Init2 = ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
Modem Type = Analog Modem
Phone = 060110
ISDN = 0
Username = [email protected]
Init1 = ATZ
Password = **************
Modem = /dev/ttyS0
Baud = 115200


the other configuration i dont have it here because ia am in the work  
right now

>
> The command    mv  /etc/wvdial.conf    myfile.txt    makes a copy  
> without changing the original file.
>
> Please hide the password   as you had done before.
>
> I will send you a file modified to use the TP-LINK modem and  
> instructions how to use it .
>
> I also need to know what you do to start the other modem before  
> giving the command wvdial to use it, because there are several ways  
> to do it.
>
> Do you give a command    slmodemd   to start the driver just before  
> you need to connect, or is the driver started automatically when you  
> boot?

let see, to start the external modem , the tp-link i use

wvdial

to start the smartlink internal modem i use

wvdial interno

later i'll send yopu the entire file ok,,

and i conect only of that way, i dont use the way that are you saying
>
>
>
> On 07/13/2011 05:33 PM, [email protected] wrote:
>
>> "Jacques Goldberg" <[email protected]> escribió:
>>
>>> Juan,
>>>
>>> 1-In the listing which you have sent,  islanis.txt, there is  
>>> outout of the first four commands only.
>>> The output for
>>>
>>> wvdial |  tee  -a  islanis.txt
>>
>> here is the missing part
>>
>>
>> root@ubuntu:/home/juan# wvdial
>> --> WvDial: Internet dialer version 1.60
>> --> Initializing modem.
>> --> Sending: ATZ
>> ATZ
>> OK
>> --> Sending: ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
>> ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0
>> OK
>> --> Modem initialized.
>> -> Sending: ATDT060110
>> --> Waiting for carrier.
>> ATDT060110
>> --> Timed out while dialing.  Trying again.
>> --> Sending: ATDT060110
>> --> Waiting for carrier.
>> ATDT060110
>>
>>
>>
>>
>>
>>
>>>
>>> is missing.
>>>
>>> So I cannot know what happens when you try to connect with wvdial  !!!
>>>
>>> Also your /etc/wvdial.conf   contains a section for   /dev/ttySL0
>>>
>>> And finally   /dev/modem  too points to   /dev/ttySL0
>>>
>>> This ambiguity between    ttySL0 and ttyS0 may fool the system.
>>>
>>> If wvdial tries to start ttySL0  but it is your TP-LINK that is  
>>> connected to the wall, it cannot connect to the phone company, and  
>>> this is exactly the problem which you reported.
>>>
>>> Please try
>>>
>>> 1-to remove /dev/modem       with command     rm/dev/modem
>>> 2-to remove the script which starts /dev/ttySL0  if it is still  
>>> there.    A way to know for sure is the command      lsmod     
>>> which should NOT show the driver for the other modem (the one you  
>>> used before trying to use TP-LINK)
>>> 3-to remove   /etc/wvdial.conf     with command    rm  /etc/wvdial.conf
>>> 4-to run wvdialconf again
>>> 5-to edit it for the username, phone number, and password as you have done
>>> 6-to start    wvdial
>> ok so, you say that i have to delete /dev/modem and /dev/ttysl0,  
>> but if i delete them, how i'll comunicate with you, because the  
>> smartlink modem is the way that i am using to comunicate with you,  
>> if this, later of this action can not work properly how can i  
>> restart de configuration to send you the other parts,am afraid of  
>> that,remember that i am new in this world,and other peoples said to  
>> me that i can have working some mothems in the same operating  
>> system, help please
>>> with a very simple basic /etc/wvdial.conf   conaining only ONE  
>>> modem ,    /dev/ttyS0
>>>
>>> What you sent definitely shows that the software is recognizing  
>>> the TP-LINK modem as expected. Thus, if wvdial  fails, it can only  
>>> be because the file   /etc/wvdial.conf is bad.
>>>
>>> This is why I suggested that you rebuild it from the beginning  
>>> without adding sophistications.
>>>
>>> Jacques
>>>
>>> On 07/13/2011 07:53 AM, juan alejandro martines linares wrote
>>>> El mié, 13-07-2011 a las 10:59 0300, Jacques Goldberg escribió:
>>>>> Juan,
>>>>>
>>>>> Can you please, AFTER HAVING VERIFIED THAT THE TP-LINK MODEM IS
>>>>> CONNECTED TO PC AND WALL AND POWERED UP, give the  five following
>>>>> commands as superuser (that is becoming su with most Linux
>>>>> distributions, or prefixing each command with sudo if you use Debian or
>>>>> Ubuntu or a variation of Ubuntu or any other variation of Debian) ?
>>>>> They will create one file named    islanis.txt
>>>>> Edit the file by replacing the password by xxx  and send me the file. Be
>>>>> sure not to leave your  password visible when sending the file,
>>>>>
>>>>> ls -l /dev/ttyS*>  islanis.txt
>>>>> ls -l /dev/modem>>   islanis.txt
>>>>> cat /etc/wvdial.conf>>   islanis.txt
>>>>> wvdialconf  /etc/wvdial.conf  |  tee  -a  islanis.txt
>>>>> wvdial |  tee  -a  islanis.txt
>>>>
>>>> here is all the requested info, the file islanis.txt
>>>>
>>>> crw-rw---- 1 root dialout 4, 64 2011-07-13 06:45 /dev/ttyS0
>>>> crw-rw---- 1 root dialout 4, 65 2011-07-13 06:29 /dev/ttyS1
>>>> crw-rw---- 1 root dialout 4, 66 2011-07-13 06:29 /dev/ttyS2
>>>> crw-rw---- 1 root dialout 4, 67 2011-07-13 06:29 /dev/ttyS3
>>>> lrwxrwxrwx 1 root root       10 2011-07-13 06:29 /dev/ttySL0
>>>> ->  /dev/pts/0
>>>> lrwxrwxrwx 1 root root 6 2011-07-13 06:29 /dev/modem ->  ttySL0
>>>>
>>>> [Dialer Defaults]
>>>> Init = ATZ
>>>> Init1 = ATZ
>>>> Init2 = ATQ0 V1 E1 S0=0&C1&D2 +FCLASS=0
>>>> #Stupid Mode = yes
>>>> Modem Type = Analog Modem
>>>> ISDN = 0
>>>> Phone = 060110
>>>> Modem = /dev/ttyS0
>>>> Username = [email protected]
>>>> #Carrier Check = no
>>>> Password = ***********
>>>> Baud = 115200
>>>>
>>>> [Dialer interno]
>>>> Init = ATZ
>>>> Init2 = ATQ0 V1 E1 S0=0 X3&C1&D2 +MS=90
>>>> Stupid Mode = yes
>>>> Modem Type = Analog Modem
>>>> ISDN = 0
>>>> Phone = 060110
>>>> Modem = /dev/ttySL0
>>>> Username = [email protected]
>>>> Carrier Check = no
>>>> Password = *************
>>>> Baud = 460800
>>>> Editing `/etc/wvdial.conf'.
>>>>
>>>> Scanning your serial ports for a modem.
>>>>
>>>>
>>>> Found a modem on /dev/ttyS0.
>>>> Modem configuration written to /etc/wvdial.conf.
>>>>
>>>>
>>>>> Where you see>>  in these commands you MUST type  TWO>    with no space
>>>>> between the two
>>>>> Where you see |  in these commands  this is a vertical bar on your
>>>>> keyboard, usually above \  at the RIGHT SIDE of your keyboard.
>>>>>
>>>>> And please do not write in Spanish - I do not understand Spanish.
>>>> ok
>>>>
>>>>
>>>>> Jacques
>>>>>
>>>>
>>>>
>>>>
>>>> -- 
>>>>
>>>> Este mensaje le ha llegado mediante el servicio de correo  
>>>> electronico que ofrece Infomed para respaldar el cumplimiento de  
>>>> las misiones del Sistema Nacional de Salud. La persona que envia  
>>>> este correo asume el compromiso de usar el servicio a tales fines  
>>>> y cumplir con las regulaciones establecidas
>>>>
>>>> Infomed: http://www.sld.cu/
>>>
>>>
>>
>>
>>
>> ----------------------------------------------------------------
>> This message was sent using IMP, the Internet Messaging Program.
>>
>>
>> -- 
>>
>> Este mensaje le ha llegado mediante el servicio de correo  
>> electronico que ofrece Infomed para respaldar el cumplimiento de  
>> las misiones del Sistema Nacional de Salud. La persona que envia  
>> este correo asume el compromiso de usar el servicio a tales fines y  
>> cumplir con las regulaciones establecidas
>>
>> Infomed: http://www.sld.cu/
>
>



----------------------------------------------------------------
This message was sent using IMP, the Internet Messaging Program.


--

Este mensaje le ha llegado mediante el servicio de correo electronico que ofrece Infomed para respaldar el cumplimiento de las misiones del Sistema Nacional de Salud. La persona que envia este correo asume el compromiso de usar el servicio a tales fines y cumplir con las regulaciones establecidas

Infomed: http://www.sld.cu/