Re: TP-LINK External Serial Modem

"Jacques Goldberg" <[email protected]> escribió:

> This is very strange.
> Have you the possibility to try to use the TP-LINK modem under  
> Windows in your or an other computer?

yes i did it and it work perfectly


> wvdialconf on your Linux does detect the modem /dev/ttyS0
yes it detect it i saw it, and it is detected fine

> Can you switch off the power on the modem and check that wvdialconf  
> does NOT detect /dev/ttyS0 when there is no power on the modem?
  i did it too and it is detected when is powered on, and when it is  
powered off is not detected by the wvdialconf, and i probe with the  
smartlink too and do the same thing
>
> Is the cable with which you conect the modem to the PC the original  
> TP-LINK cable?

yes, it came with the original box with all  the modem staff

> Do you have an ohm meter to verify that the cable is not broken?
>
> Are you using the same phone cable to connect the internal modem and  
> the TP-LINK modem to the wall?

yes, i have only one cable i to the modem conection and i use it with  
the 2 modems
> I cannot think of any other issue than a bad cable or connector.
hey i think,why whe i do a tail -f /var/log/message with the smartlink  
modem it show various information about the process but with the  
tp-link y show nothing, think about it, is very strange

>
> Jacques
>
>
> On 07/13/2011 05:22 PM, juan alejandro martines linares wrote:
>> El mié, 13-07-2011 a las 19:30 +0300, Jacques Goldberg escribió:
>>> Having two configurations in one file makes life more complicated.
>>>
>>> I have seen your file with two sections as below:
>>>
>>>
>>> [Dialer Defaults]
>>> Init = ATZ
>>> Init1 = ATZ
>>> Init2 = ATQ0 V1 E1 S0=0&C1&D2 +FCLASS=0
>>> #Stupid Mode = yes
>>> Modem Type = Analog Modem
>>> ISDN = 0
>>> Phone = 060110
>>> Modem = /dev/ttyS0
>>> Username = [email protected]
>>> #Carrier Check = no
>>> Password = ***********
>>> Baud = 115200
>>>
>>> [Dialer interno]
>>> Init = ATZ
>>> Init2 = ATQ0 V1 E1 S0=0 X3&C1&D2 +MS=90
>>> Stupid Mode = yes
>>> Modem Type = Analog Modem
>>> ISDN = 0
>>> Phone = 060110
>>> Modem = /dev/ttySL0
>>> Username = [email protected]
>>> Carrier Check = no
>>> Password = *************
>>> Baud = 460800
>>>
>>>
>>> This model can work if you start the SL modem  with command     wvdial
>>> interno
>>> or the TP-LINK modem with command      wvdial
>>>
>>> If this is what you do then the problem comes from the TP-LINK version
>>> trying to use the modem as   /dev/modem   which is no more than a link
>>> to /dev/ttySL0   not connected to the wall.
>>>
>>> Just remove the link /dev/modem   with  command      rm /dev/modem
>>> and try again, first the TP-LINK and then the SL modem.
>>> If you ever need /dev/modem again, the command is         ln  -s
>>> /dev/ttySL0   /dev/modem
>>> (or ttyS0  if you want the TP-LINK to be /dev/modem  ).
>>> Do not forget the    -s   option in the link  (ln)   command.
>>>
>>> Be aware  that other dialers than   wvdial   define their own
>>> /dev/modem   (example kppp, qinternet). All that depends on which
>>> version of Linux you use.
>> i made all that and nothing, is still without conection, i ma in my home
>> now and the 2 configuration are these
>>
>>
>> [Dialer Defaults]
>> Init = ATZ
>> Init1 = ATZ
>> Init2 = ATQ0 V1 E1 S0=0&C1&D2 +FCLASS=0
>> Modem Type = Analog Modem
>> ISDN = 0
>> Phone = 060110
>> Modem = /dev/ttyS0
>> Username = [email protected]
>> Password = **********
>> Baud = 115200
>>
>> [Dialer interno]
>> Init = ATZ
>> Init2 = ATQ0 V1 E1 S0=0 X3&C1&D2 +MS=90
>> Stupid Mode = yes
>> Modem Type = Analog Modem
>> ISDN = 0
>> Phone = 060110
>> Modem = /dev/ttySL0
>> Username = [email protected]
>> Carrier Check = no
>> Password = ***********
>> Baud = 460800
>>
>>> Jacques
>>>
>>
>>
>>
>> --
>>
>> Este mensaje le ha llegado mediante el servicio de correo  
>> electronico que ofrece Infomed para respaldar el cumplimiento de  
>> las misiones del Sistema Nacional de Salud. La persona que envia  
>> este correo asume el compromiso de usar el servicio a tales fines y  
>> cumplir con las regulaciones establecidas
>>
>> Infomed: http://www.sld.cu/
>
>



----------------------------------------------------------------
This message was sent using IMP, the Internet Messaging Program.


--

Este mensaje le ha llegado mediante el servicio de correo electronico que ofrece Infomed para respaldar el cumplimiento de las misiones del Sistema Nacional de Salud. La persona que envia este correo asume el compromiso de usar el servicio a tales fines y cumplir con las regulaciones establecidas

Infomed: http://www.sld.cu/