D-Link DWL-G520 Problem

Hello...

I installed a D-Link DWL-G520 on my Debian Sid Box, Kernel 2.2.27
latest madwifi cvs branch.
heres the output 
####lspci -vvv

0000:00:05.0 Ethernet controller: Atheros Communications, Inc. AR5212
802.11abg NIC (rev 01)
        Subsystem: D-Link System Inc: Unknown device 3a13
        Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr-
Stepping- SERR- FastB2B-
        Status: Cap+ 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort-
<TAbort- <MAbort- >SERR- <PERR-
        Latency: 168 (2500ns min, 7000ns max), Cache Line Size: 0x08 (32
bytes)
        Interrupt: pin A routed to IRQ 11
        Region 0: Memory at e2000000 (32-bit, non-prefetchable) [size=64K]
        Capabilities: [44] Power Management version 2
                Flags: PMEClk- DSI- D1- D2- AuxCurrent=375mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
                Status: D0 PME-Enable- DSel=0 DScale=2 PME-


modprobe ath_pci :


Jun 22 10:08:03 localhost kernel: ath0: 11b rates: 1Mbps 2Mbps 5.5Mbps
11Mbps
Jun 22 10:08:03 localhost kernel: ath0: 11g rates: 1Mbps 2Mbps 5.5Mbps
11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
Jun 22 10:08:03 localhost kernel: ath0: mac 7.9 phy 4.5 radio 5.6
Jun 22 10:08:03 localhost kernel: ath0: 802.11 address: 00:11:95:94:20:d9
Jun 22 10:08:03 localhost kernel: ath0: Use hw queue 0 for WME_AC_BE traffic
Jun 22 10:08:03 localhost kernel: ath0: Use hw queue 1 for WME_AC_BK traffic
Jun 22 10:08:03 localhost kernel: ath0: Use hw queue 2 for WME_AC_VI traffic
Jun 22 10:08:03 localhost kernel: ath0: Use hw queue 3 for WME_AC_VO traffic
Jun 22 10:08:03 localhost kernel: ath0: Atheros 5212: mem=0xe2000000, irq=11



ath0      Protokoll:Ethernet  Hardware Adresse 00:11:95:94:20:D9
          inet Adresse:192.168.0.4  Bcast:192.168.0.255  Maske:255.255.255.0
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0


and ###iwconfig
ath0      IEEE 802.11  ESSID:""
          Mode:Managed  Frequency:2.442 GHz  Access Point: FF:FF:FF:FF:FF:FF
          Bit Rate:1 Mb/s   Tx-Power:50 dBm   Sensitivity=0/3
          Retry:off   RTS thr:off   Fragment thr:off
          Encryption key:off
          Power Management:off
          Link Quality=0/94  Signal level=-95 dBm  Noise level=-95 dBm
          Rx invalid nwid:0  Rx invalid crypt:0  Rx invalid frag:0
          Tx excessive retries:0  Invalid misc:0   Missed beacon:0
not really the burner :-)

can anyone help me??
-- 
Uwe Hof- Redmann
registered as user #115895 with the Linux Counter, http://counter.li.org
This is machine #70591
http://www.bilderschmiede.com